logo

Industrial Silicone Sealant 4 – 40C Neutral Cure For Window Installation ASTM C920

Place of Origin: China
Brand Name: YT
Certification: ISO9001, Work safety standardization certificate
Model Number: 338
Minimum Order Quantity: 50 metric tons
Price: Custom Product Production
Packaging Details: Standard Packaging
Delivery Time: Customized production depends on the situation.
Payment Terms: L/C, D/A, D/P, T/T, Western Union
Supply Ability: Custom Product Production
Inquiry Now
Get A Quote
Specifications
Highlight Features

Industrial Silicone Sealant 4C Neutral Cure

,

Industrial Silicone Sealant 40C Neutral Cure

,

automotive silicone sealant ASTM C920

Name:
High Temperature Silicone Sealant
Curing Type:
One-Component, Neutral Cure
Application Temperature:
4–40°C
Sag:
0mm
Skin-Over Time:
0.5 Hours
Extrusion Rate:
≥580mL/min
Packaging:
300mL Cartridge; 590mL Sausage
Application:
Waterproof Window Installation, Indoor And Outdoor Wall Joints, And General Construction Sealing
Product Description

4–40°C Neutral-Cure Industrial Silicone Sealant for Window Installation: ASTM C920 Selection Guide

 

Problem

 

Window perimeter joints are exposed to rain, temperature cycles, and minor movement between the frame and the wall. Aluminum, glass, concrete, brick, and PVC expand at different rates. If the sealant has inadequate adhesion, insufficient joint thickness, or poor sag control, edge separation and cracking can create a direct path for water penetration.

The stated 4–40°C range is also frequently misunderstood. It describes the recommended substrate temperature during application; it is not evidence of the cured sealant’s long-term service-temperature range.

 

Cause

 

Waterproofing failure usually results from a combination of joint movement, surface contamination, and unsuitable joint geometry.

Dust, moisture, oil, release agents, and loose particles prevent direct contact between the silicone and the substrate. The sealant may initially appear bonded but separate after thermal movement. If the sealant layer is too thin, stress becomes concentrated along the edges instead of being distributed through the joint.

Below 4°C, frost or an invisible condensation film may remain on the frame or wall. Above 40°C, extrusion behavior and surface curing may change. Applying the sealant outside the specified conditions can therefore increase the risk of uneven joints and adhesion failure.

 

Solution

 

This one-component, neutral-cure Industrial Silicone Sealant requires no on-site mixing and can be dispensed with a standard caulking gun. Before installation, adhesion and compatibility tests should be completed on the actual aluminum, glass, concrete, coated metal, or PVC substrate.

The measured sag is 0mm, compared with the listed maximum requirement of 3mm. This helps the sealant retain its profile in vertical window joints. The measured skin-over time is 0.5 hours, reducing the period during which airborne dust can contaminate the surface. Skin formation, however, must not be confused with complete curing.

The measured extrusion rate is at least 580mL/min, indicating smooth dispensing under the stated test conditions. Continuous extrusion helps avoid gaps between separate beads.

Before sealing, remove water, dust, oil, and loose material. Apply masking tape to both sides, fill the joint continuously, and tool the bead before skin formation. Tooling improves contact with the joint surfaces and removes trapped air. The supplied instructions recommend a sealant thickness of at least 5mm and application within one hour after surface cleaning.

ASTM C920 covers cured elastomeric joint sealants and classifies them by type, grade, movement class, and use. A purchase specification should therefore identify the required Type, Grade, Class, and Use, instead of requesting “ASTM C920” without a classification.

 

Specifications

 

Specification

Product Data

Relevance to Window Sealing

Product type

One-component, neutral cure

Ready for gun application

Application temperature

4–40°C

Substrate temperature during installation

Appearance

Uniform paste without bubbles, skin, or gel

Supports consistent application

Sag

0mm; requirement ≤3mm

Suitable for vertical joints

Skin-over time

0.5h; requirement ≤3h

Surface skinning, not complete curing

Extrusion rate

≥580mL/min; requirement ≥150mL/min

Supports continuous dispensing

Tensile adhesion at 23°C

Measured value: 0.5

Unit must be verified from the test report

Cohesive adhesion

No failure

Result under the stated test method

Recommended thickness

≥5mm

Helps avoid an excessively thin bead

Colors

Black, grey, white, or customized

Matches different frames and walls

Packaging

300mL cartridge; 590mL sausage

For corresponding caulking guns

Storage and shelf life

Below 27°C; 9 months

For unopened packaging under stated conditions

Documented standard

JC/T 485-2007

ASTM C920 compliance requires separate evidence

 

Application

 

Suitable applications include waterproof perimeter sealing between aluminum window frames and walls, general indoor or outdoor window-installation joints, decorative panel edges, and other non-structural construction joints.

The product must not be used for structural glazing, continuous immersion, permanently wet joints, or completely enclosed spaces. Compatibility testing is required for PVC, coated aluminum, rubber components, and materials that may release plasticizers or oil.

 

FAQ

 

Is 4–40°C the long-term service-temperature range?

No. It is the recommended application range. Long-term service limits require separate heat-aging and low-temperature test data.

Does the product comply with ASTM C920?

The available data does not establish compliance. Request a test report showing the applicable Type, Grade, Class, and Use classification.

Can the joint be exposed to rain after 0.5 hours?

Not based on skin-over time alone. A surface skin does not mean the sealant has fully cured. Protect the joint from rain and movement during curing.

Will it bond to every window material without primer?

This cannot be assumed. Surface treatments, PVC formulations, coatings, and concrete moisture can change adhesion. Test the actual production substrates before full installation.

 
 
Related Products
Send An Inquiry