Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Low-Speed EV Rear Body Silicone Sealant For Sheet-Metal Seam Filling And Sealing
Problem | Why Can Multi-Directional Rear Body Seams Develop Bead Interruptions?
The rear body of a low-speed four-wheel electric vehicle can contain several connected sheet-metal sections. Rear panels, side-body panels and other tail structures may create horizontal, vertical and corner joints.
The technical objective is not simply to cover the visible seam with sealant. The material needs to form a continuous bead matched to the actual joint geometry.
A horizontal bead may remain consistent while the transition into a vertical section becomes thinner because nozzle direction, travel speed or distance from the substrate changes.
For this reason, rear-body sealing should focus on continuity throughout the complete sealing path rather than simply increasing sealant volume.
Cause | Why Can a Deeper Overlap Continue Curing After Skin Formation?
Rear-body structures can contain both shallow seams and deeper overlaps.
4C and 5C have specified skin-over times of 20–40 minutes, while 6C is 20–30 minutes. Their specified cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
Skin-over time describes the exposed surface condition. Cure rate describes progressive curing through the sealant section.
A deeper rear-panel joint may therefore continue curing after its visible surface has already formed a skin.
Solution | Match 4C, 5C or 6C to the Actual Rear-Body Joint
Start by identifying the actual sheet metal, surface condition, joint width, depth, corners and overlap geometry.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
The data demonstrates why hardness and tensile strength should be evaluated independently rather than converted into one overall ranking.
A practical workflow is:
Rear-Body Substrate → Joint Width/Depth → Corner and Overlap Geometry → Property Comparison → Continuous Dispensing → Cure Management → Actual-Part Verification
How It Works
Black silicone is continuously dispensed along rear-body sheet-metal seams to fill local gaps.
Long horizontal sections require consistent bead dimensions. At vertical transitions and corners, adjacent bead sections should be checked for complete connection.
Where multiple joints meet, excessive material at one point cannot compensate for an interruption elsewhere.
After dispensing, curing progresses through the sealant section. Deeper overlaps should therefore be managed using actual bead dimensions together with the specified 1.2–3 or 1.5–3 mm/24h cure rate.
Application Scenarios
This page focuses on rear-body panel seams, rear-to-side-body transitions, tail-panel overlaps, corners and local multi-directional sheet-metal joints on low-speed four-wheel electric vehicles.
The supplied information supports sheet-metal bonding and sealing applications but does not provide individual adhesion qualification data for every coated steel, plated metal or vehicle design.
Actual production substrates should therefore be verified before volume application.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |