Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Low-Speed EV Wheel-House Silicone Sealant For Curved Sheet-Metal Seam Filling And Sealing
Problem | Why Is the Wheel-House Area More Difficult to Seal Than a Straight Sheet-Metal Seam?
The wheel-house area of a low-speed four-wheel electric vehicle differs significantly from a conventional straight body seam. Its curved profile and connections with surrounding panels require the dispensing nozzle to continuously change direction and angle.
If material flow remains constant while nozzle travel speed changes around the curved section, the resulting bead cross-section may become inconsistent. A bead can remain uniform along a straight section but become thinner, accumulate excess material, or lose continuity around curved transitions.
The key requirement is therefore not simply whether sealant has been applied. The process should create a continuous bead matched to the curved geometry, joint width and joint depth.
Cause | Why Are Curved Joints More Likely to Develop Variations in Sealant Thickness?
During straight-line dispensing, nozzle angle and distance from the substrate are relatively easy to maintain. Both conditions change continuously when the nozzle follows the wheel-house curve.
If dispensing volume remains constant while travel speed varies, different sections can develop different bead dimensions.
Cure behavior is also affected by sealant depth. 4C and 5C have specified skin-over times of 20–40 minutes, while 6C is 20–30 minutes. The specified cure rate is 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
A deeper curved overlap can therefore continue curing internally even after the exposed surface has reached its skin-over condition.
Solution | How Should 4C, 5C and 6C Be Selected for Wheel-House Joints?
Start by identifying the actual wheel-house substrate, surface treatment, joint width and joint depth. Then compare the mechanical and processing properties of each grade.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A hardness and 1.4–1.6 MPa tensile strength. 6C provides 60 Shore A hardness and 1.9–2.0 MPa tensile strength.
These values should not be converted into a simple “best grade” ranking. For example, 5C has the higher hardness value, while 6C has the higher specified tensile-strength range. The two parameters describe different material characteristics.
A more appropriate selection sequence is:
Actual Substrate → Curved Joint Geometry → Joint Width/Depth → Hardness and Tensile Strength → Dispensing Process → Cure Management → Actual-Part Verification
How to Choose | Which Parameters Matter Most for Wheel-House Sealing?
Where cured hardness is important, compare 50–60 Shore A for 4C, 65 Shore A for 5C and 60 Shore A for 6C.
Where tensile strength is an important selection factor, the corresponding values are 1.85 MPa, 1.4–1.6 MPa and 1.9–2.0 MPa.
Production timing also requires separate consideration of skin-over time and cure rate. Although 6C has a specified skin-over time of 20–30 minutes, this does not demonstrate complete curing through a deeper sealant section.
Wheel-house projects should therefore consider substrate type, curved joint dimensions, mechanical properties and curing conditions together.
Application Scenarios | Which Low-Speed EV Wheel-House Joints Can This Sealant Be Used For?
The product is intended for applications such as curved wheel-house sheet-metal seams, wheel-house-to-adjacent-panel interfaces, local overlap joints and curved transition seams on low-speed four-wheel electric vehicles.
The supplied product information supports automotive sheet-metal bonding and sealing applications. However, it does not provide wheel-house-specific stone-chip, salt-spray, abrasion or long-term corrosion-resistance test data.
For this reason, the product page can describe sheet-metal joint filling and sealing, but claims such as “stone-chip resistant,” “long-term anti-corrosion,” or “salt-spray resistant” should only be added when corresponding test documentation is available.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |