Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Low-Speed EV Front Body Silicone Sealant For Sheet-Metal Seam Filling And Sealing
Problem | Why Is Covering the Visible Front-Body Seam Not Enough?
The front body area of a low-speed four-wheel electric vehicle can contain multiple sheet-metal interfaces. Compared with a long, relatively regular side seam, this area may contain shorter sealing paths, overlaps, corners and joints running in different directions.
Applying sealant only over the visible surface may leave deeper sections inadequately filled. Corners and joint intersections also require changes in nozzle direction, which can affect bead dimensions.
Effective sealing therefore requires a bead designed around the actual width, depth and direction of the joint.
Cause | Why Are Corners and Joint Intersections More Difficult to Seal?
During straight-line dispensing, nozzle speed and direction are relatively easy to maintain. At a corner or panel intersection, nozzle angle, travel speed and distance from the substrate may change.
Without corresponding control of material delivery, these changes can produce a thinner bead, incomplete connection or local accumulation.
Cure depth is another consideration. 4C and 5C have specified skin-over times of 20–40 minutes, while 6C is 20–30 minutes. Cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
A deeper overlap may therefore continue curing after its exposed surface has reached skin-over condition.
Solution | Combine Joint Geometry with Mechanical Specifications
First identify the actual metal substrate, surface condition and joint geometry before comparing 4C, 5C and 6C.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
The highest hardness value does not correspond to the highest tensile-strength value, demonstrating why the two properties should be considered separately.
A practical workflow is:
Actual Substrate → Joint Width/Depth → Corners and Intersections → Hardness/Tensile Properties → Continuous Dispensing → Cure Management → Actual-Part Verification
How It Works
Black silicone sealant is continuously dispensed along front-body panel seams and overlaps to fill local gaps.
Straight sections require consistent bead dimensions. Corners, joint intersections and transitions between front and side body panels require additional inspection to confirm that adjacent bead sections are properly connected.
Adding excessive sealant at one point cannot compensate for an interruption elsewhere in the sealing path.
After application, curing progresses through the sealant section. Actual joint depth should therefore be considered together with the specified cure rate before subsequent assembly operations.
How to Choose
For hardness, compare 50–60 Shore A for 4C, 65 for 5C and 60 for 6C.
For tensile strength, compare 1.85 MPa for 4C, 1.4–1.6 MPa for 5C and 1.9–2.0 MPa for 6C.
For surface processing time, 6C has a specified skin-over time of 20–30 minutes, while 4C and 5C are 20–40 minutes.
For B2B project evaluation, the customer should also provide substrate type, surface treatment, joint dimensions and downstream assembly timing. The supplied information does not provide individual adhesion qualification for every coated metal or low-speed EV design, so actual production parts should be verified before volume application.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |