Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Low-Speed EV Underbody Silicone Sealant For Sheet-Metal Seam Filling And Sealing
Problem | Why Is Surface Coverage Alone Not Enough for Underbody Seams?
The underbody of a low-speed four-wheel electric vehicle can contain panel seams, overlaps and edge joints. Unlike easily visible exterior joints, underbody interfaces may include narrow gaps, deeper overlaps and directional transitions.
Simply covering the visible seam may create a continuous-looking surface while leaving deeper sections insufficiently filled.
Long sealing paths also require controlled dispensing. Changes in nozzle travel speed or material delivery can produce uneven bead dimensions.
Underbody sealing should therefore focus on joint geometry, filling condition, bead continuity and curing behavior rather than sealant volume alone.
Cause | Why Does Joint Depth Affect Process Timing?
Shallow panel seams and deeper overlaps can have different sealant depths even when the same grade is used.
4C and 5C have specified skin-over times of 20–40 minutes, while 6C is 20–30 minutes. The specified cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
Skin-over time therefore describes surface condition rather than complete curing throughout the bead.
For deeper underbody overlaps, actual sealant dimensions should be considered together with cure rate when planning downstream processing.
Solution | Match the Grade to the Actual Underbody Joint
First identify the actual panel material, surface condition, joint width and depth.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
These parameters should be evaluated independently. The highest hardness value does not automatically represent the most suitable grade for every underbody joint.
A practical workflow is:
Panel Material → Surface Condition → Joint Width/Depth → Grade Properties → Continuous Filling → Bead Inspection → Cure Management → Actual Underbody Verification
How It Works
Black silicone sealant is continuously applied along underbody panel seams and into the gaps that require sealing.
Long straight joints require controlled dispensing speed and material delivery. Overlap ends, corners and joint intersections should be checked for complete bead connection.
Excessive material at one point cannot compensate for an interruption or insufficient filling elsewhere.
After application, curing progresses through the sealant section. Deeper joints should therefore be managed according to actual bead dimensions together with the specified 1.2–3 or 1.5–3 mm/24h cure rate.
FAQ
Should underbody joints simply use a very thick sealant bead?
Not necessarily. Bead dimensions should match the actual joint geometry. Continuous filling is more important than excessive material.
Is 6C fully cured after 20–30 minutes?
No. This value is the specified skin-over time. Its cure rate is 1.2–3 mm/24h.
Does the 65 Shore A hardness make 5C automatically the best choice for underbody seams?
No. Hardness is only one parameter. Tensile strength, joint dimensions and actual process requirements should also be evaluated.
Can this product be marketed as a long-term underbody anti-corrosion sealant?
The supplied information does not provide salt-spray, corrosion-classification or anti-corrosion lifetime data. Such claims should not be made without corresponding test documentation.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |