Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
ISO 9001 One-Component Industrial Silicone Sealant for Temperature-Resistant Indoor and Outdoor Wall Joints
Problem
Indoor and outdoor wall joints are repeatedly affected by temperature changes, rain, ultraviolet exposure, and minor substrate movement. Concrete walls, metal frames, glass, and decorative panels have different thermal expansion characteristics. When they expand or contract at different rates, an unsuitable sealant may crack, separate from the substrate, or allow water to enter the joint.
Sagging is another concern in vertical applications. If the uncured sealant moves downward after application, the upper section of the joint may contain insufficient material while the lower section becomes excessively thick. This creates an uneven appearance and may interrupt the sealing path.
Buyers must also distinguish between application temperature and long-term service temperature. The specified 4–40°C range refers to the substrate temperature during installation. It should not be presented as the cured sealant’s maximum continuous operating-temperature range.
Cause
Wall-joint failure is frequently associated with substrate preparation and installation conditions.
Dust, water, oil, release agents, and loose particles can form an intermediate layer between the silicone and the substrate. The sealant may initially appear attached but later separate when the joint is exposed to movement or moisture. Some plastics, rubbers, and bituminous materials can release plasticizers, oil, or solvents, causing discoloration, softening, or adhesion failure.
Below 4°C, frost, condensation, or an invisible water film may remain on the surface. Above 40°C, the sealant’s surface reaction and application behavior may change. An excessively thin sealant layer may also be unable to fill the joint correctly or accommodate normal installation tolerances.
Solution
This one-component, neutral-cure Industrial Silicone Sealant requires no on-site mixing and can be applied using a standard sealant gun. It is intended for general indoor and outdoor wall joints, window and door perimeters, and non-structural construction sealing.
The measured sag value is 0mm, compared with the specified requirement of no more than 3mm. This helps the sealant retain its intended profile in vertical joints. The measured skin-over time is 0.5 hours, reducing the period during which dust may attach to the exposed surface. Its measured extrusion rate is at least 580mL/min, indicating smooth dispensing under the stated test conditions and supporting the formation of a continuous sealant bead.
Before application, remove dust, moisture, oil, and loose material from the substrate. Adhesion and compatibility tests should be carried out on the actual concrete, metal, glass, or decorative panel. Apply masking tape along both sides of the joint, dispense the sealant continuously, and tool it before skin formation. Proper tooling improves contact with the joint surfaces and helps remove trapped air.
The supplied instructions recommend a sealant thickness of at least 5mm. Application should preferably be completed within one hour after cleaning to reduce the risk of surface contamination.
ISO 9001 indicates that the manufacturer uses a documented quality management system. It does not independently certify the sealant’s adhesion, weather resistance, movement capability, or long-term temperature resistance.
Key Specifications
|
Specification |
Value or Test Result |
Technical Explanation |
|---|---|---|
|
Product type |
One-component neutral-cure silicone sealant |
Ready to apply without on-site mixing |
|
Appearance |
Fine, uniform paste without bubbles, skinning, or gel particles |
Supports consistent dispensing |
|
Application temperature |
4–40°C |
Refers to substrate temperature during installation |
|
Sag |
0mm; requirement: ≤3mm |
Suitable for vertical wall and frame joints |
|
Skin-over time |
0.5h; requirement: ≤3h |
Actual time depends on temperature, humidity, and joint size |
|
Extrusion rate |
≥580mL/min; requirement: ≥150mL/min |
Indicates smooth dispensing under the stated test conditions |
|
Tensile adhesion at 23°C |
Measured value: 0.5 |
The source does not show the unit; verify it before publication |
|
Cohesive adhesion result |
No failure |
Reported under the specified adhesion test |
|
Recommended thickness |
≥5mm |
Helps avoid an excessively thin sealant layer |
|
Colors |
Black, grey, white, or customized |
Can be matched to walls, frames, and panels |
|
Packaging |
300mL cartridge; 590mL foil sausage |
Suitable for corresponding sealant guns |
|
Storage |
Below 27°C in a cool, dry place |
Keep the original packaging unopened and dry |
|
Shelf life |
9 months |
Applies under the specified storage conditions |
|
Referenced standard |
JC/T 485-2007 |
ISO 9001 is a quality management system standard |
Application
Typical applications include indoor and outdoor wall joints, waterproof sealing around window and door frames, interior decoration joints, and general sealing around kitchen or sanitary fixtures.
The product must not be used for structural glazing. It is also unsuitable for continuous water immersion, permanently wet joints, completely enclosed spaces, or poorly ventilated locations. Compatibility testing is required for materials that may release oil, plasticizers, or solvents.
How to Choose
Consider five factors before purchasing:
Application conditions: The substrate temperature should remain within 4–40°C, and the surface must be clean and dry.
Joint orientation: Vertical joints require a non-sag or low-sag formulation.
Substrate type: Test adhesion separately on concrete, metal, glass, and decorative panels.
Application grade: General waterproof filling differs from structural glazing, continuous immersion, and high-temperature equipment sealing.
Technical evidence: Do not rely only on ISO 9001 or a “Temperature Resistance” claim. Check the application range, adhesion results, movement capability, weathering data, and verified service-temperature limits.