Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Structural Glazing Silicone Sealant: How to Build Long-Term Outdoor Bonding Performance for Airport Curtain Walls
Problem | Why Is Long-Term Outdoor Performance Critical for Airport Facades?
Airport terminals commonly use large-area glass curtain walls with extensive facade surfaces and numerous glazing units. These systems remain exposed to sunlight, temperature variation, rain, and cyclic wind loads. A structural glazing silicone sealant must form a continuous bond between glass and aluminum framing so that loads acting on the glass can be transferred to the curtain wall structure.
For airport curtain wall projects, “long-term outdoor stability” should not simply mean that the sealant does not visibly crack. The more important questions are whether the bonding interface remains intact, whether sufficient tensile adhesion is maintained, and whether the silicone layer can accommodate deformation caused by temperature and wind loading.
Cause | Why Can Airport Curtain Walls Develop Long-Term Bonding Risks?
Airport facades experience a combination of wind loading, temperature variation, solar exposure, and material movement. Large glass panels can deflect under wind pressure, while differences in thermal expansion between glass and aluminum create relative movement. The structural silicone joint therefore experiences repeated tensile loading and deformation.
A “curtain wall dedicated formula” should also be supported by technical evidence rather than treated as a marketing label. If compatibility with coated glass or aluminum finishes has not been verified, or if the structural bite is insufficient for the project design wind load, localized stress concentration or interface adhesion failure may occur even when the sealant itself meets its technical specification.
Solution | Use Verifiable Performance Data for Curtain Wall Sealant Selection
398 Silicone Structural Sealant uses a one-component, neutral-cure system and is specified for glass curtain walls, aluminum curtain walls, and various metal structural applications, providing a technical basis for evaluation in airport facade projects.
At 23°C, its measured tensile adhesion strength reaches 0.95 MPa, compared with a requirement of ≥0.60 MPa. Elongation at maximum strength reaches 145%, compared with a requirement of ≥100%, while the recorded adhesion failure area is 0%.
These parameters should be evaluated together. The 0.95 MPa value provides measurable evidence of structural adhesion under the specified test conditions; 145% describes tensile deformation behavior; and the 0% adhesion failure result provides information about bonding-interface integrity under the corresponding test conditions.
For airport projects, adhesion and compatibility tests should still be performed with the actual glass, aluminum profiles, and coatings. Structural joint dimensions should also be engineered according to panel dimensions, design wind loads, and facade configuration.
Technical Specifications
Property | Requirement | Typical Result |
Cure Type | Neutral Cure | Neutral Cure |
Components | One Component | One Component |
Tensile Adhesion Strength at 23°C | ≥0.60 MPa | 0.95 MPa |
Elongation at Maximum Strength | ≥100% | 145% |
Adhesion Failure Area | ≤5% | 0% |
Shore A Hardness | 20–60 | 42 |
Sag | ≤3 mm | 0 mm |
Tack-Free Time | ≤3 h | 0.5 h |
Extrusion Rate | ≥120 mL/min | ≥490 mL/min |
How It Works | How Does Structural Silicone Maintain a Continuous Load Path?
After curing, 398 structural silicone forms a continuous bonding layer between the glass and curtain wall frame. When wind pressure acts on airport facade glazing, the load is transferred from the glass through the structural silicone bond to the aluminum frame and then into the supporting building structure.
The 0.95 MPa tensile adhesion strength and 145% elongation at maximum strength should be considered together. The former represents adhesion performance under specified test conditions, while the latter describes deformation behavior during tensile loading. A Shore A hardness of 42 provides a reference for cured material hardness, while 0 mm sag supports controlled application in vertical joints.
Long-term outdoor performance, however, depends on the combined effect of material properties, engineered joint dimensions, substrate testing, and installation control. Since the available technical data does not specify a verified outdoor service life or artificial weathering duration, fixed lifetime claims should not be made without additional test evidence.