Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
YT-PV400 Solar Panel Sealant for Aluminum PV Frame Bonding and Sealing
Problem | Why Is Initial Adhesion Not Enough for Aluminum PV Frames?
PV module frame sealing commonly involves an interface between aluminum and glass. For this type of assembly, judging a sealant only by whether it initially adheres to the surface is not sufficient.
The adhesive needs to continuously cover the designed bonding area, contact the relevant substrates and form a suitable layer after curing. Interrupted application, contaminated surfaces or incomplete filling can create weak points even when the visible joint appears to contain enough adhesive.
For this reason, PV frame sealant selection should consider the substrates, joint configuration, cured condition and application process together.
Cause | Why Does an Aluminum-to-Glass Interface Need an Elastic Seal?
Aluminum and glass are different substrate materials. During module assembly, the adhesive must reach the designed bonding area and establish contact with the relevant surfaces before curing.
The available YT-PV400 information specifically identifies aluminum and glass among its applicable materials. Other listed substrates include different types of backsheets, PPO/PA junction boxes and ceramic materials.
The product information also states that YT-PV400 forms an elastomer after curing. It therefore creates an elastic adhesive layer rather than functioning simply as a rigid gap-filling material.
This provides a more technically grounded way to describe the product than making a general claim of “high stability.”
Solution | Using YT-PV400 for Aluminum PV Module Frames
YT-PV400 is a one-component photovoltaic sealant. Before application, aluminum and glass bonding areas should be clean and dry, with dust and obvious contamination removed.
The sealant should then be applied continuously according to the actual frame and joint design. Increasing adhesive quantity locally should not be used as a substitute for continuous application and proper substrate contact.
After application, YT-PV400 cures to form an elastomeric layer between the relevant materials.
Packaging should also be matched to production requirements. Available formats include 400 ml cartridges, 4 kg pails and 270 kg drums, with 12 pieces per carton for the 400 ml format. The 270 kg drum is particularly relevant where bulk adhesive supply is required.
Specifications
|
Item |
Specification |
|---|---|
|
Product Name |
YT-PV400 Solar Panel Sealant |
|
System |
One-Component |
|
Primary Substrates |
Aluminum and Glass |
|
Other Listed Substrates |
Backsheets, PPO/PA Junction Boxes, Ceramic, etc. |
|
Cured State |
Elastomer |
|
Functions |
Bonding, Sealing and Potting |
|
Electrical Property |
Good Insulation |
|
Protection |
Moisture, Dust and Impact Protection |
|
Cartridge |
400 ml/pc, 12 pcs/carton |
|
Pail |
4 kg |
|
Drum |
270 kg |
|
Storage |
Cool and dry conditions below 27°C |
|
Color |
According to Customer Requirements |
How It Works
The frame sealing process can be described as:
Surface Preparation → Continuous Application → Substrate Contact → Curing → Elastic Sealing Interface
Continuous contact with both aluminum and glass is important. A visually filled joint should not automatically be treated as evidence of complete substrate contact.
According to the supplied information, YT-PV400 forms an elastomer after curing. However, the current source does not provide numerical movement capability, tensile strength or elongation-at-break values, so such figures should not be added to the product page without the corresponding TDS or test report.
How to Choose
Start with the substrates. For an aluminum-to-glass PV frame interface, verify that both materials are included in the product's documented application range. YT-PV400 specifically lists aluminum and glass.
Next, consider the system and cured state. YT-PV400 is one-component and forms an elastomer after curing.
Finally, match the packaging to the production process. Available formats are 400 ml, 4 kg and 270 kg. The 270 kg drum can be considered where bulk adhesive feeding is required.
Actual adhesion suitability should still be verified against the specific aluminum surface condition, glass type and production process before large-scale application.