Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Low-Speed EV Windshield Silicone Sealant for Glass-to-Body Bonding and Sealing
Problem | Why Can Windshield Perimeter Joints Become Sealing Weak Points?
The windshield of a low-speed four-wheel electric vehicle creates a continuous joint with the surrounding body frame. Effective sealing therefore depends on more than whether the sealant initially adheres to the glass.
The complete perimeter bead needs to remain continuous, while the sealant section must be appropriate for the actual gap.
Lower windshield edges, A-pillar corners and transitions between horizontal and vertical sections can be particularly sensitive to changes in dispensing speed and bead dimensions. Insufficient material or an interrupted bead at these locations can create a weak section in an otherwise continuous sealing path.
Road vibration adds another mechanical condition after assembly. For this reason, windshield sealant selection should consider joint geometry, hardness, tensile strength and cure rate together.
Cause | Why Does Skin-Over Time Not Mean Full Cure?
Sealant depth around a windshield is not necessarily uniform. Corners, dimensional tolerances and locally wider gaps can create deeper sealant sections.
4C and 5C have specified skin-over times of 20–40 minutes, while 6C is 20–30 minutes.
However, the cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
Surface skin formation therefore does not demonstrate that the complete bead depth has reached the same cured condition. Skin-over time and cure rate should be treated as separate process parameters.
Solution | Start with the Actual Windshield Joint
Identify the actual glass, body-frame surface and joint dimensions before comparing grades.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
The data illustrates why the highest hardness value should not automatically be interpreted as the highest overall mechanical performance.
A practical selection sequence is:
Actual Glass/Frame → Joint Width and Depth → Mechanical Properties → Continuous Dispensing → Cure Management → Assembly Verification
How It Works
Black silicone sealant is applied continuously around the interface between the windshield and vehicle frame, filling local gaps and forming a perimeter sealing path.
Corners, A-pillar edges, upper/lower bead transitions and start/end points require particular inspection. A uniform bead along most of the windshield cannot compensate for a significant interruption at one location.
After application, curing progressively develops through the sealant layer. Production timing should therefore consider actual bead depth together with the specified 1.2–3 or 1.5–3 mm/24h cure rate.
Application Scenarios
Based on the supplied product information, the sealant can be used for glass bonding and sealing applications associated with low-speed electric vehicles.
This page specifically addresses windshield-to-body perimeter joints and similar glass-edge sealing locations.
The supplied data does not provide individual adhesion results for every glass coating, painted metal system, primer or vehicle design. Compatibility should therefore be verified on the actual production substrates before volume application.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |