Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Low-Speed EV Door Silicone Sealant for Sheet-Metal Seam Filling and Sealing
Problem | Why Do Low-Speed EV Door Seams Develop Weak Sealing Areas?
Doors used on low-speed four-wheel electric vehicles contain inner and outer panels, folded edges, overlaps and local metal joints. Effective sealing therefore requires more than simply applying sealant over the visible surface.
If the bead becomes interrupted around a corner or insufficient material is applied where the joint becomes wider or deeper, sections of the seam may remain inadequately filled.
Vehicle vibration and repeated door opening and closing also introduce mechanical action after assembly. Door sealing should therefore consider joint geometry, material properties, bead continuity and curing conditions together.
Cause | Why Is Surface Skin Formation Not Enough?
Door hem-flange joints can vary in width and depth, particularly around corners and overlapping metal sections.
The supplied specifications show skin-over times of 20–40 minutes for 4C and 5C and 20–30 minutes for 6C.
However, the specified cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
A surface that has already formed a skin therefore does not demonstrate that material deeper inside the door joint has reached the same cured condition.
Solution | Select the Grade from the Actual Door Joint
First identify the door-panel substrate, surface condition, joint geometry and actual sealant depth.
Then compare the mechanical specifications. 4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
These values show why hardness and tensile strength should be evaluated separately. The grade with the highest hardness does not automatically have the highest tensile-strength value.
A practical selection sequence is:
Door Substrate → Joint Geometry → Bead Dimensions → Hardness/Tensile Properties → Skin-Over and Cure Rate → Actual-Part Verification
How It Works
Black silicone sealant is continuously applied along the hem flange or overlap between the inner and outer door panels, filling local gaps and creating a continuous sealing path.
Straight sections should maintain a consistent bead, while corners and dimensional transitions require additional attention for interruptions or insufficient filling.
After application, the exposed sealant develops a surface skin and curing continues through the bead. Actual process timing should therefore consider sealant depth together with the specified cure rate.
How to Choose
Where cured hardness is an important criterion, compare 50–60 Shore A for 4C, 65 for 5C and 60 for 6C.
Where tensile strength is relevant, the specified values are 1.85 MPa for 4C, 1.4–1.6 MPa for 5C and 1.9–2.0 MPa for 6C.
For surface processing time, 6C has a specified 20–30 minute skin-over time, compared with 20–40 minutes for 4C and 5C.
The final selection should still be verified on the actual low-speed EV door substrate and joint design rather than relying on one parameter alone.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |