logo

Electric Vehicle Lights Chemical Resistant Silicone Clear Automotive For Lens To Housing

Place of Origin: China
Brand Name: YT
Certification: ISO9001, Work safety standardization certificate
Model Number: Automotive Adhesive
Minimum Order Quantity: 50 metric tons
Price: Custom Product Production
Packaging Details: Standard Packaging
Delivery Time: Customized production depends on the situation.
Payment Terms: L/C, D/A, D/P, T/T, Western Union
Supply Ability: Custom Product Production
Inquiry Now
Get A Quote
Specifications
Highlight Features

Electric Vehicle Lights chemical resistant silicone

,

ISO9001 chemical resistant silicone

,

Lens to Housing clear automotive silicone

Product Name:
Automotive Grade Silicone Sealant
Grade:
4C / 5C / 6C
Density:
1.5–1.7 G/cm³
Hardness:
50–65 Shore A, Depending On Grade
Tensile Strength:
1.4–2.0 MPa, Depending On Grade
Skin-Over Time:
20–40 Min, Depending On Grade
Cure Rate:
1.2–3 Mm/24h, Depending On Grade
Application:
Bonding, Gap Filling And Sealing Of Low-Speed EV Windshield-to-Body Joints
Product Description

Low-Speed EV Lamp Sealant | Silicone Sealant for Electric Vehicle Lights
 
Problem | Why Can Low-Speed EV Lamp Joints Become Sealing Weak Points?
 
Headlamps and taillights used on low-speed four-wheel electric vehicles normally contain a lens, housing and internal components. Once assembled, the lens-to-housing interface forms a continuous perimeter joint.
Curved edges, sharp transitions and bead start/end locations can make consistent dispensing more difficult. If the bead becomes locally thin, interrupted or insufficient to fill the channel, that section can become a weak point within the overall sealing path.
Vehicle vibration adds another operating condition after installation. Sealant selection should therefore consider hardness, tensile strength, joint geometry and curing behavior, rather than skin-over time alone.
 
Cause | Why Does Lamp-Channel Geometry Affect Curing?
 
Lamp channels are not necessarily straight or uniform in depth. Corners and styling transitions can create locally deeper sections.
The supplied data specifies 20–40 minute skin-over times for 4C and 5C and 20–30 minutes for 6C.
Their cure rates, however, are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
Surface skin formation therefore should not be interpreted as complete curing through a deeper lamp joint.
 
Solution | Select by Substrate, Channel Geometry and Process
 
Start by identifying the actual lens and housing materials. Then check channel width, depth and corner geometry before comparing grades.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
These values provide measurable selection criteria, but the highest hardness value should not be interpreted as universally superior performance.
A practical workflow is:
Lens/Housing Substrate → Channel Width and Depth → Hardness/Tensile Properties → Continuous Dispensing → Cure Time → Actual Lamp Verification
 
How It Works
 
Black silicone is dispensed into the lens-to-housing joint and forms a continuous bead around the lamp perimeter.
The objective is not simply to create a thick bead in one section, but to maintain continuity around the complete sealing path. Corners, curved transitions and bead start/end points deserve particular inspection.
After application, curing progresses through the sealant section. For deeper channels, subsequent assembly timing should consider the specified 1.2–3 or 1.5–3 mm/24h cure rate, rather than relying only on surface condition.
 
How to Choose
 
For cured hardness, compare 50–60 Shore A for 4C, 65 for 5C and 60 for 6C.
For tensile strength, the specified values are 1.85 MPa for 4C, 1.4–1.6 MPa for 5C and 1.9–2.0 MPa for 6C.
For skin-over time, 6C is specified at 20–30 minutes, compared with 20–40 minutes for 4C and 5C.
Because the supplied information does not provide individual adhesion data for every lamp lens and housing material, actual low-speed EV lamp assemblies should be verified before volume production.
 
Technical Specifications

 
 

Property

4C

5C

6C

Appearance

Uniform Black Paste

Uniform Black Paste

Uniform Black Paste

Density at 25°C

1.5–1.7 g/cm³

1.5–1.7 g/cm³

1.5–1.7 g/cm³

Volatile Content at 150°C

3–4%

3–4%

3–4%

Hardness

50–60 Shore A

65 Shore A

60 Shore A

Tensile Strength

1.85 MPa

1.4–1.6 MPa

1.9–2.0 MPa

Skin-Over Time

20–40 min

20–40 min

20–30 min

Cure Rate

1.5–3 mm/24h

1.2–3 mm/24h

1.2–3 mm/24h

Related Products
Send An Inquiry