Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Low-Speed EV Side Window Silicone Sealant For Glass-To-Frame Joint Sealing
Problem | Why Can Side-Window Corners Become Sealing Weak Points?
After a fixed side window is installed on a low-speed four-wheel electric vehicle, a continuous joint is formed between the glass edge and body frame.
Although the glass area may be smaller than a windshield, the sealing path still includes horizontal sections, vertical sections and corners. Changes in dispensing speed around these transitions may reduce the local bead size.
Dimensional variation between the glass and frame can also change the actual gap. A fixed dispensing volume may therefore provide adequate filling in one section but insufficient filling in another.
Effective side-window sealing consequently depends on bead continuity, joint dimensions and cure management rather than initial adhesion alone.
Cause | Why Does the Same Skin-Over Time Not Mean the Same Cure Depth?
The actual sealant depth around a side window may vary, particularly around corners and pillar interfaces.
4C and 5C have specified skin-over times of 20–40 minutes, while 6C is 20–30 minutes. Their cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
Skin-over time describes the exposed surface condition. Cure rate describes the progressive curing of material through the sealant section. The two values should therefore not be treated as interchangeable.
Solution | Match the Grade to the Actual Side-Window Joint
First identify the actual glass, body-frame substrate and surface condition. Then inspect joint width and depth around the complete glass perimeter.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
These specifications provide measurable selection criteria, but no single value represents overall suitability.
A practical selection sequence is:
Glass/Frame Substrate → Joint Width and Depth → Hardness and Tensile Properties → Bead Continuity → Cure Management → Actual Assembly Testing
How It Works
Black silicone is continuously applied between the side-window glass and body frame, filling local gaps and creating a complete perimeter sealing path.
Straight sections require consistent bead dimensions, while particular attention should be given to the corners and transitions between horizontal and vertical beads.
After dispensing, curing progresses through the sealant section. Actual bead depth should therefore be considered together with the specified 1.2–3 or 1.5–3 mm/24h cure rate before subsequent production steps.
FAQ
Is 6C fully cured after its 20–30 minute skin-over period?
No. Full cure depends on bead depth and the specified 1.2–3 mm/24h cure rate.
Does the 65 Shore A hardness of 5C automatically make it more suitable for side windows?
No. Hardness is one selection parameter and should be considered together with tensile strength, joint geometry and substrate compatibility.
Can the sealant be used for every low-speed EV side-window system?
The supplied information supports glass bonding and sealing applications, but does not provide individual qualification data for every vehicle, glass coating or frame surface. Actual assemblies should be verified before volume use.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |