Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Problem | Why Can Low-Speed EV Roof Seams Develop Local Sealing Weak Points?
The roof of a low-speed four-wheel electric vehicle may contain joints between the roof panel and surrounding body structure. These interfaces can create long metal seams, edge joints and local overlaps.
Effective sealing depends on forming a continuous bead that matches the actual gap. If dispensing speed changes along a long roof seam, or if joint width and depth vary, some sections may receive less sealant than others.
Vehicle vibration provides an additional operating condition after assembly. Roof-seam sealing should therefore consider joint dimensions, bead continuity, cured mechanical properties and curing conditions together.
Cause | Why Do Long Roof Seams Require Dispensing Control?
Long sealing paths can expose variations in nozzle travel speed and material delivery. When the bead reaches front or rear corners, the dispensing direction also changes.
These transitions can produce locally thin beads, interruptions or excessive material if dispensing is not controlled.
Curing must also be evaluated separately from surface skin formation. 4C and 5C have specified skin-over times of 20–40 minutes, while 6C is 20–30 minutes. The cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
A dry surface therefore does not demonstrate complete curing through a deeper joint.
Solution | Match the Grade to the Actual Roof Seam
Start by identifying the roof-panel substrate, surface condition, joint width and sealant depth.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
These parameters describe different material characteristics and should not be converted into a simple overall performance ranking.
A practical workflow is:
Roof Substrate → Joint Width/Depth → Mechanical Properties → Continuous Dispensing → Corner Inspection → Cure Management → Actual-Part Verification
How It Works
Black silicone sealant is continuously dispensed along roof-panel joints and overlap areas to fill local gaps and create a continuous sealing path.
Long straight sections require consistent bead dimensions. Front and rear transitions and roof-to-side-body interfaces require additional inspection for thin sections, interruptions or excessive accumulation.
After application, curing progresses from the exposed surface through the sealant section. Deeper joints therefore require process timing based on actual bead dimensions and the specified cure rate rather than skin-over time alone.
Application Scenarios
This page focuses on low-speed EV roof-panel seams, roof-to-side-body interfaces, front and rear roof transitions, and local sheet-metal overlap joints.
For B2B production projects, actual joint dimensions, metal surface condition and downstream assembly timing should be considered when selecting a grade.
The supplied product information supports automotive sheet-metal bonding and sealing applications but does not provide individual adhesion qualification data for every coated metal or low-speed EV roof system. Actual production substrates should therefore be verified before volume use.
Technical Specifications
Property | 4C | 5C | 6C |
|---|---|---|---|
Appearance | Uniform Black Paste | Uniform Black Paste | Uniform Black Paste |
Density at 25°C | 1.5–1.7 g/cm³ | 1.5–1.7 g/cm³ | 1.5–1.7 g/cm³ |
Volatile Content at 150°C | 3–4% | 3–4% | 3–4% |
Hardness | 50–60 Shore A | 65 Shore A | 60 Shore A |
Tensile Strength | 1.85 MPa | 1.4–1.6 MPa | 1.9–2.0 MPa |
Skin-Over Time | 20–40 min | 20–40 min | 20–30 min |
Cure Rate | 1.5–3 mm/24h | 1.2–3 mm/24h | 1.2–3 mm/24h |