Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Low-Speed EV Body Side Silicone Sealant For Sheet-Metal Joint Filling And Sealing
Problem | Why Can Body-Side Seams Have Locally Insufficient Filling?
Low-speed four-wheel electric vehicle body sides can contain multiple panel interfaces, overlaps and pillar connections. These joints do not necessarily form a uniform straight channel.
Joint width and depth can change along the body structure. If a fixed dispensing volume is used without considering these dimensional changes, a narrow section may be adequately filled while a wider or deeper section receives insufficient material.
Transitions around pillars, corners and bead start/end points also change the dispensing direction. Effective sealing therefore depends on matching the sealant bead to the actual joint geometry rather than simply increasing material volume.
Cause | Why Can One Body-Side Bead Have Different Curing Conditions?
A body-side sealing path may contain both shallow panel seams and locally deeper overlaps.
4C and 5C have specified skin-over times of 20–40 minutes, while 6C is 20–30 minutes. However, the specified cure rate is 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
A surface that has reached its skin-over condition therefore does not demonstrate that a deeper section has reached the same curing state.
For production control, skin-over time and cure rate should be treated as separate process parameters.
Solution | Select 4C, 5C or 6C from the Actual Body-Side Joint
Start by identifying the actual metal panel and surface condition. Then evaluate joint width, depth, overlaps and corner geometry.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
These values show why hardness and tensile strength should be evaluated independently rather than converted into a single overall performance ranking.
A practical selection sequence is:
Actual Panel → Joint Width/Depth → Hardness and Tensile Properties → Continuous Dispensing → Transition Inspection → Cure Management → Actual-Part Verification
How to Choose
For cured hardness, compare 50–60 Shore A for 4C, 65 for 5C and 60 for 6C.
For tensile strength, the supplied values are 1.85 MPa for 4C, 1.4–1.6 MPa for 5C and 1.9–2.0 MPa for 6C.
Where surface processing time is relevant, 6C has a specified skin-over time of 20–30 minutes, compared with 20–40 minutes for 4C and 5C.
A shorter skin-over time should not be interpreted as proof of faster complete curing through a deep seam. Actual bead dimensions and cure rate remain important.
FAQ
Should a body-side seam simply use a thicker bead?
Not necessarily. Sealant dimensions should match the actual joint. Excess material cannot replace correct joint filling and continuous dispensing.
Is 6C fully cured after 20–30 minutes?
No. This is the specified skin-over time. Its cure rate is 1.2–3 mm/24h, so internal curing depends on bead depth.
Does 65 Shore A make 5C automatically better for body-side seams?
No. Hardness is only one property and should be evaluated together with tensile strength, joint geometry and substrate conditions.
Can the sealant be applied to every low-speed EV body-side panel?
The supplied information supports sheet-metal bonding and sealing, but does not provide individual adhesion qualification for every coated metal system. Actual production substrates should be verified before volume use.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |