logo

UV Curable Acrylic Adhesive Sealant One Component For Plastic Electronic Assemblies

Place of Origin: China
Brand Name: YT
Certification: ISO9001, Work safety standardization certificate
Model Number: Acrylic Adhesive
Inquiry Now
Get A Quote
Specifications
Highlight Features

UV Curable Acrylic Adhesive

,

Acrylic Adhesive One Component

,

Plastic Electronic uv glue for acrylic

Product Name:
One-Component UV-Curable Adhesive Sealant
Base Resin:
Urethane Acrylate
Curing Method:
Curing Method
Recommended Light Source:
LED, 365 Nm, UVA
Reference Viscosity:
10,000–20,000 Cps At 10 Rpm
PC Bonding Reference:
PC–PC Shear Strength ≥8 MPa
Inspection Feature:
Fluorescent Under UV Light
Intended Use:
Structural Bonding And Sealing Of Industrial And Consumer Electronic Devices, Particularly Plastic Substrates
Product Description

One-Component UV-Curable Adhesive Sealant For Plastic Electronic Assemblies

 

Problem | Has the Entire Bond Line Cured?

 

In plastic electronic assemblies, a hardened adhesive surface does not establish that the entire bond line has cured sufficiently. Exposed edges, shaded sections and areas with uneven adhesive thickness need separate attention. Without checking these locations, an assembler may have limited evidence about the condition of the adhesive at the bonding interface.

The practical objective is to establish a curing process for the actual component geometry, rather than assess curing from surface appearance alone.

 

Cause | Substrates and Joint Geometry Affect UV Exposure

 

This adhesive sealant cures under ultraviolet irradiation. Plastic light transmission, lamp position and obstruction by surrounding components can change the exposure reaching the adhesive, even when equipment settings remain unchanged.

The document reports a curing depth greater than 120 μm, but does not provide the complete conditions behind that value. It should therefore not be interpreted as evidence that any adhesive thickness will cure during one exposure.

 

Solution | Validate the Process on Actual Components

 

The product is a one-component, urethane acrylate-based UV-curable adhesive sealant. Before application, remove dust, oil and surface moisture. Confirm that the cleaning agent is compatible with the plastic substrate before using it on production parts.

Use the documented recommendations—365 nm LED irradiation, 500 mW/cm² and 10 seconds—as starting conditions for trials. Evaluate curing at the intended adhesive thickness and in locations with restricted exposure.

The listed PC-to-PC shear strength of ≥8 MPa provides a reference for polycarbonate bonding assessments. It does not establish equivalent performance on other plastics, different grades or different joint configurations.

 

Technical Specifications

 

Property

Document Reference Value

Resin system

Urethane acrylate

Components

One-component

Viscosity

10,000–20,000 cps at 10 rpm

Recommended light source

LED, 365 nm, UVA

Recommended intensity / time

500 mW/cm² / 10 s

Curing depth

>120 μm

Hardness

Shore D 75 ± 5

Shear strength

≥8 MPa, PC–PC

 

Application | Plastic Bonding and Sealing in Electronics

 

The document identifies structural bonding and sealing in industrial and consumer electronic devices, particularly on plastic substrates.

For a specific assembly, confirm the material grade, joint dimensions and loading conditions. A PC-to-PC test result should support initial material evaluation, while tests on representative components establish suitability for the intended assembly.

 

How It Works | Fluorescence Supports Coverage Inspection

 

The adhesive layer fluoresces under UV light, allowing operators to inspect where material has been applied and identify possible missed areas.

Fluorescence supports coverage inspection. It does not, by itself, demonstrate sufficient curing or confirm bond strength. Coverage inspection and assessment of the cured joint address different questions and should be evaluated accordingly.

 

How to Choose | Check the Substrate and Light Path First

 

Start with the plastic type and the path through which UV light reaches the adhesive. Then establish the intended bond-line thickness and verify the exposure conditions on representative parts.

For shaded sections, do not assume that another curing mechanism will complete the process. The supplied document provides no basis for moisture curing or thermal curing. Any joint that prevents adequate UV exposure requires further technical assessment before this product is selected.

Related Products
Send An Inquiry