logo

Polycarbonate Bonding Acrylic Epoxy Adhesive Sealant Acrylic Based Glue

Place of Origin: China
Brand Name: YT
Certification: ISO9001, Work safety standardization certificate
Model Number: Acrylic Adhesive
Minimum Order Quantity: 50 metric tons
Price: Custom Product Production
Delivery Time: Customized production depends on the situation.
Payment Terms: T/T, Western Union
Supply Ability: Custom Product Production
Inquiry Now
Get A Quote
Specifications
Highlight Features

Polycarbonate Bonding acrylic epoxy adhesive

,

Bonding acrylic epoxy adhesive

,

Urethane acrylate acrylic based glue

Product Name:
One-Component UV-Curable Adhesive Sealant
Base Resin:
Urethane Acrylate
Curing Method:
Curing Method
Recommended Light Source:
LED, 365 Nm, UVA
Reference Viscosity:
10,000–20,000 Cps At 10 Rpm
PC Bonding Reference:
PC–PC Shear Strength ≥8 MPa
Inspection Feature:
Fluorescent Under UV Light
Intended Use:
Bonding And Sealing Electronic Devices, With Fluorescence-assisted Coverage Inspection
Product Description

One-Component UV-Curable Adhesive Sealant For Polycarbonate Bonding
 
Product Positioning and Intended Use
 
This one-component UV-curable adhesive sealant is based on urethane acrylate resin. The document identifies structural bonding and sealing applications in industrial and consumer electronic devices, particularly on plastic substrates.
A PC-to-PC shear strength of ≥8 MPa is listed as a reference for polycarbonate bonding assessment. This figure is not a design allowable stress for a finished component.
 
Problem | Can PC Test Data Be Used Directly in Component Design?
 
Shear strength is often a primary comparison point when selecting an adhesive for PC plastic. However, a specimen result does not directly establish the load capacity of an actual assembly.
Multiplying the listed strength by the nominal bonding area is insufficient to determine a component’s permissible load. The joint geometry, loading direction and manufacturing conditions also require assessment.
 
Cause | Actual Joints Have Different Loading and Curing Conditions
 
The documented value of ≥8 MPa applies to PC-to-PC specimens tested using GB/T 7124-2008. Complete specimen preparation and curing conditions are not supplied.
An actual joint may experience peel, eccentric loading or impact in addition to shear. Local stresses near joint edges and areas with restricted UV access can also affect the result. These differences limit how directly a specimen value can be transferred to a component.
 
Solution | Validate the Bonding Process on Representative Joints
 
First identify the PC grade, surface condition and joint dimensions. Remove dust, oil and surface moisture, and confirm that the cleaning agent is compatible with the plastic.
Use the document’s recommended conditions—a 365 nm LED source, 500 mW/cm² and 10 seconds—as starting points for curing trials. Verify the actual adhesive thickness and light access before finalizing the process.
Test representative joints in the principal loading direction expected during use. Record whether failure occurs at the interface, within the adhesive or in the substrate. This information helps explain the joint’s behavior beyond the peak load alone.
 
Technical Specifications
 

Property

Document Reference Value or Description

Source

Product name

UV-curable adhesive sealant

Document description

Resin and components

Urethane acrylate; one-component

Description and parameter table

Appearance

Colorless, translucent liquid

Parameter table

Viscosity

10,000–20,000 cps at 10 rpm

Parameter table

PC–PC shear strength

≥8 MPa; GB/T 7124-2008

Parameter table

Recommended curing conditions

LED, 365 nm; 500 mW/cm²; 10 s

Parameter table

Curing depth

>120 μm

Parameter table

Intended use

Structural bonding and sealing of electronic devices, particularly plastic substrates

Document description

 
Application | Material Selection for Plastic Electronic Assemblies
 
The PC-to-PC result supports including this product in a polycarbonate bonding evaluation. Specific housings, brackets or internal component joints require confirmation.
A material name alone does not establish suitability for every component location or loading condition.
 
How to Choose | Assess Loading Direction Before Comparing Strength
 
For joints loaded mainly in shear, shear testing provides relevant evidence. Where peel or eccentric loads are present, add tests that represent those conditions.
Bond-line thickness must also accommodate the assembly gap while remaining compatible with the verified UV curing process.
 
FAQ | Does Transparent PC Always Allow Sufficient Curing?
 
No. Check the actual PC grade, color, thickness and transmission at 365 nm. Visual transparency does not establish adequate UV exposure at the adhesive layer. Confirm curing using representative components.

Related Products
Send An Inquiry