logo

Urethane Acrylate UV Curable Electronic Device Silicone Acrylic Adhesive For Bonding

Place of Origin: China
Brand Name: YT
Certification: ISO9001, Work safety standardization certificate
Model Number: Acrylic Adhesive
Inquiry Now
Get A Quote
Specifications
Highlight Features

urethane acrylate acrylic adhesive

,

urethane acrylate acrylic based adhesive

,

bonding acrylic adhesive

Product Name:
UV-Curable Adhesive Sealant For Electronic Devices
Base Resin:
Urethane Acrylate
Curing Method:
Curing Method
Recommended Light Source:
LED, 365 Nm, UVA
Reference Viscosity:
10,000–20,000 Cps At 10 Rpm
PC Bonding Reference:
PC–PC Shear Strength ≥8 MPa
Inspection Feature:
Fluorescent Under UV Light
Intended Use:
Structural Bonding And Sealing Of Plastic Substrates In Industrial And Consumer Electronic Devices
Product Description

Urethane Acrylate UV-Curable Adhesive Sealant For Electronic Devices

 

Product Positioning and Intended Use

 

This one-component adhesive sealant uses a urethane acrylate resin system and cures under ultraviolet irradiation. The document identifies structural bonding and sealing applications in industrial and consumer electronic devices, particularly on plastic substrates.

Volume resistivity data provide a reference for material selection where electrical insulation is relevant. These data do not replace electrical verification of the completed assembly.

 

Problem | Do Insulation Data Establish Component Suitability?

 

An adhesive used in electronics may need to support both plastic bonding and electrical insulation. A single resistivity value cannot establish whether the applied layer is continuous, its thickness is appropriate or the assembled insulation path meets the design requirements.

Material selection must therefore consider the actual joint and the electrical function it is expected to perform.

 

Cause | Material Properties and Assembly Performance Require Different Assessments

 

The document lists a volume resistivity of ≥1×10¹⁴ Ω·cm using GB/T 1410-2006. Complete specimen preparation and environmental conditions are not provided.

Volume resistivity describes a material’s resistance to electrical conduction through its bulk. It cannot be directly converted into the insulation resistance or permissible operating voltage of a finished component.

Likewise, a bonding result does not establish electrical performance. These properties address different requirements and need separate supporting evidence.

 

Solution | Verify Layer Formation, Curing and Electrical Performance

 

Identify the plastic grade, joint dimensions and insulation requirements before establishing the application process. Clean the substrate using a compatible method, apply the adhesive and inspect the intended coverage.

Use the documented 365 nm LED source, 500 mW/cm² irradiance and 10-second exposure as starting conditions for curing trials. Pay particular attention to shaded locations and thicker deposits.

After establishing curing, conduct electrical and bonding tests appropriate to the assembly requirements. Record the results separately so that acceptance of one property does not imply acceptance of the other.

 

Technical Specifications

 

Property

Document Reference Value or Description

Source

Product name

UV-curable adhesive sealant

Document description

Resin and components

Urethane acrylate; one-component

Description and parameter table

Volume resistivity

≥1×10¹⁴ Ω·cm; GB/T 1410-2006

Parameter table

Recommended source

LED, 365 nm, UVA

Parameter table

Recommended irradiance and time

500 mW/cm²; 10 s

Parameter table

Curing depth

>120 μm

Parameter table

PC–PC shear strength

≥8 MPa

Parameter table

Intended use

Structural bonding and sealing of electronic devices, particularly plastic substrates

Document description

 

Application | Material Assessment for Bonding and Insulation Requirements

 

Electronic device and plastic substrate applications are documented. Any specific insulation location requires confirmation.

The available information does not establish suitability as a high-voltage insulating adhesive or potting compound, and it does not represent electrical certification of a completed device.

 

How to Choose | Match the Parameter to the Required Test

 

First establish whether the project requires material resistivity data, assembly insulation resistance or voltage-withstand verification. Select the corresponding assessment rather than treating these terms as interchangeable.

Use bonding tests to evaluate the joint’s mechanical function and electrical tests to evaluate its insulation function.

 

FAQ | Can the Permissible Operating Voltage Be Calculated from the Table?

 

No. The original table labels one property “breakdown voltage” but expresses it in kV/mm. The meaning requires clarification. Do not multiply that figure by adhesive thickness to assign an assembly operating voltage.

 

Key Parameters for Use in the Copy

 

Parameter

Appropriate Use

Source

Volume resistivity ≥1×10¹⁴ Ω·cm

Material insulation selection reference

Parameter table

PC–PC shear strength ≥8 MPa

Reference for PC bonding evaluation

Parameter table

365 nm; 500 mW/cm²; 10 s

Starting conditions for curing trials

Parameter table

Related Products
Send An Inquiry