logo

Moisture Curing Reactive Woodworking Lamination Hot Melt Adhesives For Bonding

Place of Origin: China
Brand Name: YT
Certification: ISO9001,
Model Number: Hot Helt Adhesives
Inquiry Now
Get A Quote
Specifications
Highlight Features

wd hot helt adhesives

,

wd hot melt adhesives

,

pur hot helt adhesives

Product Name:
WD PUR Hot Melt Adhesive For Woodworking Flat Lamination
Chemistry And Cure:
Reactive Polyurethane Hot Melt Adhesive; Moisture-curing
Melt Viscosity:
15,000±3,000 MPa·s At 120°C; ISO 3219
Open Time:
4±2 Min
Application Temperature:
120–150°C In The Specification Table; 110–150°C In The Operating Instructions; Clarification Required
Peel Force On PVC:
≥40 N/25 Mm
Solids Content:
100%
Application:
Wood Flat Lamination And WPC Board Flat Lamination
Product Description

WD PUR Hot Melt Adhesive for Woodworking Flat Lamination | Moisture-Curing Reactive Polyurethane Adhesive

 

Product Overview

 

WD is a moisture-curing reactive polyurethane hot melt adhesive with 100% solids, primarily intended for wood flat lamination, including WPC board flat lamination. It provides initial strength after application and cooling to support subsequent processing, with heat and water resistance after full cure. Specific material combinations and processing conditions should be verified through lamination trials.

 

Problem | Does Initial Setting Mean Bonding Is Complete?

 

Wood flat lamination requires both suitable processing speed and performance after curing. WD provides initial strength after application and cooling to support subsequent operations. However, the fact that laminated surfaces hold together does not indicate full cure. Initial setting and final curing must be distinguished when assessing heat and water resistance.

 

Cause | Cooling and Moisture Curing Are Different Stages

 

WD uses a moisture-reactive polyurethane hot melt system. Cooling helps establish initial strength, while moisture curing contributes to subsequent property development. The document describes heat and water resistance after full cure. Inspection immediately after pressing therefore cannot replace performance testing after curing.

 

Solution | Establish Trial Conditions Around Temperature and Pressing Intervals

 

Record the substrate combination, actual application temperature and interval before pressing. WD has a melt viscosity of 15,000±3,000 mPa·s at 120°C, and the temperature must accompany the value. The stated open time is 4±2 minutes, but the test conditions are unspecified. Confirm the actual coating and pressing sequence through lamination trials.

 

Technical Specifications

 

Parameter

Value or Description

Conditions and Notes

Product Model

WD

Model listed in the document

Chemical Composition

Reactive polyurethane hot melt adhesive

PUR hot melt system

Curing Mechanism

Moisture-curing

Equipment sealing and air exposure require attention

Solids Content

100%

Stated value

Color

Water-white

Visual inspection

Density

1.1±0.05 g/cm³

Standard listed: GB/T 13477-2002

Melt Viscosity

15,000±3,000 mPa·s

At 120°C; ISO 3219

Open Time

4±2 min

Test conditions not specified

Softening Temperature

85±5°C

Does not establish maximum service temperature after curing

Application Temperature

120–150°C in the specification table; 110–150°C in the operating instructions

Inconsistent ranges; clarification required before use

Peel Force on PVC

≥40 N/25 mm

Complete specimen construction and test conditions not specified

Packaging

20 kg/drum or 170 kg/drum

As stated in the document

Storage Conditions

Cool, dry conditions at 10–25°C

As stated in the storage instructions

Shelf Life

6 months in original packaging

As stated in the document

 

Application | Wood and WPC Board Flat Lamination

 

The document identifies wood flat lamination and specifically lists WPC board flat lamination. The stated peel force on PVC of ≥40 N/25 mm can serve as a reference for relevant testing. However, the complete laminated construction is not specified, so this value does not establish suitability for every PVC film and board combination. Specific combinations require validation.

 

How It Works | Why Does Adhesive Supply Equipment Need Sealing?

 

The adhesive cures through a reaction with moisture. The document therefore calls for attention to dispensing equipment sealing and advises against prolonged air exposure after opening. Adhesive supply arrangements should match the processing sequence to reduce unnecessary open exposure.

 

FAQ | Does a 24-Hour Waiting Period Mean Full Cure?

 

No. The document recommends testing assembled panels after 24 hours but does not specify a full-cure time. The two application temperature ranges also require clarification before use. The document warns that temperatures above 150°C may deform PVC film.

Related Products
Send An Inquiry