Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Low-Speed EV Floor Panel Silicone Sealant For Seam And Overlap Filling
Problem | Why Is “Can This Sealant Bond Plastic?” Not Specific Enough for a Plastic Component Project?
Low-speed four-wheel electric vehicles can contain different types of plastic components, but “plastic” does not represent one universal substrate. Polymer type, surface condition, component geometry and joint dimensions can all affect the actual bonding and sealing result.
The supplied product information explicitly includes plastic bonding and sealing within its application scope. However, it does not provide separate adhesion-strength values for specific polymers such as ABS, PP or PC.
For a B2B project, grade selection should therefore begin with the actual substrate, joint geometry and production process, rather than a general assumption about all plastics.
Cause | Why Does the Same Silicone Sealant Still Need Verification on Different Plastic Components?
Plastic components can differ not only in material but also in geometry.
Curved surfaces, narrow joints around clips, component edges and changing assembly gaps can create different requirements for bead continuity and gap filling.
The mechanical properties of 4C, 5C and 6C also differ. 4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
Therefore, the fact that all three grades are black silicone sealants does not mean that their cured mechanical properties are identical.
Solution | How Should the Plastic Substrate and Joint Conditions Be Used to Determine Sealant Selection?
For a B2B project, the customer should ideally provide the plastic type, surface condition, joint width and depth, bonding area and downstream assembly timing.
Once the substrate has been identified, 4C, 5C and 6C can be compared using hardness, tensile strength, skin-over time and cure rate.
4C and 5C have specified skin-over times of 20–40 minutes, while 6C is 20–30 minutes. The specified cure rate is 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
Where the exact polymer is unknown or substrate-specific adhesion data is unavailable, actual component testing should be completed before making a specific adhesion-performance claim.
A practical selection sequence is:
Plastic Type → Surface Condition → Joint Dimensions → 4C/5C/6C Property Screening → Sample Application → Cure Management → Actual-Part Verification
How to Choose | How Should 4C, 5C and 6C Be Compared for Plastic Components?
For cured hardness, compare 50–60 Shore A for 4C, 65 Shore A for 5C and 60 Shore A for 6C.
For tensile strength, compare 1.85 MPa for 4C, 1.4–1.6 MPa for 5C and 1.9–2.0 MPa for 6C.
Where surface processing time is important, compare 20–40 minutes for 4C/5C with 20–30 minutes for 6C.
These parameters should not be evaluated independently of the actual plastic substrate. Where no specific adhesion data is available for a particular polymer, testing with the actual material is recommended before volume production.
Application Scenarios | Which Low-Speed EV Plastic Component Applications Are Supported by the Available Product
Information?
According to the supplied product information, the sealant system can be used for plastic bonding and sealing in automotive and electric-vehicle assembly.
For low-speed four-wheel EV applications, this can include plastic-component interfaces, edge joints and assembly gaps requiring bonding or sealing.
However, the available information does not provide separate adhesion-strength data for ABS, PP, PC or other specific polymers. The product page should therefore not broaden this into an unsupported claim that the sealant is suitable for “all plastics.”
Where a dedicated SEO page for a specific polymer is required, corresponding adhesion or compatibility test documentation should first be checked.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |