Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Low-Speed EV Glass-To-Metal Silicone Sealant For Frame Joint Bonding And Sealing
Problem | Why Should a Glass-to-Metal Joint Not Be Inspected Only from the Glass Side?
Glass installation in a low-speed four-wheel electric vehicle is not a single-substrate application. The sealant is positioned between the glass and the vehicle's metal frame, creating a system involving the glass surface, silicone bead and metal-frame surface.
Checking only the glass side does not account for the condition of the metal frame, its coating or the actual assembly gap.
Joint dimensions can also vary around the glass perimeter. Straight edges, corners and frame transitions may have different widths or depths. If a fixed dispensing rate does not match these changes, some sections may be sufficiently filled while others develop a thinner bead or incomplete connection.
The objective is therefore to create a continuous sealing path matched to the actual glass-to-metal joint geometry.
Cause | Why Can the Inside of a Glass Joint Continue Curing After the Surface Has Formed a Skin?
A glass-to-metal joint has a defined sealant cross-section. The exposed surface changes first, while deeper sections continue through the curing process.
4C and 5C have specified skin-over times of 20–40 minutes, while 6C is 20–30 minutes. However, 4C has a specified cure rate of 1.5–3 mm/24h, while 5C and 6C are 1.2–3 mm/24h.
These values describe different process characteristics.
Skin-over time describes the exposed surface condition, while cure rate describes progressive curing through the sealant section.
A skin formed around the glass perimeter therefore does not demonstrate that the complete sealant cross-section has reached the same curing condition.
Solution | How Should Glass, Metal Frame and Joint Geometry Be Evaluated Together?
First identify the actual glass type and bonding surface. Then identify the metal-frame material, coating and surface condition. Finally, determine joint width, depth, corner geometry and downstream assembly timing.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A and 1.4–1.6 MPa, while 6C provides 60 Shore A and 1.9–2.0 MPa.
These properties should be evaluated separately. For example, 5C has the higher hardness value, while 6C has the higher specified tensile-strength range. Neither parameter alone determines suitability for the complete assembly.
A practical selection sequence is:
Glass Type → Metal Frame and Surface Condition → Joint Width/Depth → Property Comparison → Continuous Dispensing → Cure Management → Actual-Part Verification
How It Works | How Does Silicone Sealant Form a Continuous Joint Between Glass and a Metal Frame?
Black silicone sealant is continuously applied along the interface between the glass edge and metal frame, filling the actual assembly gap.
Along straight sections, dispensing rate and nozzle travel speed should be controlled to maintain consistent bead dimensions. At glass corners, frame transitions and areas where joint dimensions change, bead continuity requires additional inspection.
A large amount of sealant at one location cannot compensate for an interruption elsewhere in the perimeter joint.
After application, downstream processing should consider actual bead depth together with the specified 1.2–3 or 1.5–3 mm/24h cure rate, rather than relying only on the skin-over time.
How to Choose | Which Parameters Should Be Compared for a Glass-to-Metal Sealing Project?
Start with the actual substrates rather than selecting a grade by its model number.
For cured hardness, compare 50–60 Shore A for 4C, 65 Shore A for 5C and 60 Shore A for 6C.
For tensile strength, compare 1.85 MPa for 4C, 1.4–1.6 MPa for 5C and 1.9–2.0 MPa for 6C.
Where surface processing time matters, 4C and 5C specify 20–40 minutes, while 6C specifies 20–30 minutes skin-over time. Deeper sealant sections should also be evaluated using the specified cure rate.
The available information supports glass bonding and sealing applications, but does not provide specific adhesion-strength data for every glass surface, surface treatment or metal coating combination. Actual assembly verification is therefore recommended before volume production.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |