Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Electric Microcar Tail Lamp Silicone Sealant For Lens-To-Housing Bonding And Sealing
Problem | Why Does a Small Tail Lamp Still Require Careful Control of Perimeter Bead Continuity?
An electric microcar tail lamp may be relatively compact, but its perimeter joint can contain curves, corners and changes in joint width. Seal quality should therefore not be evaluated simply by checking whether sealant is visible around the lamp.
The more important question is whether the bead remains continuous along the actual lens-to-housing interface.
At sharp corners, curved edges and bead start/end points, nozzle direction changes frequently. If travel speed changes without corresponding control of material flow, local accumulation, thinner bead sections or incomplete bead connections can occur.
Tail-lamp sealing should therefore focus on continuous filling around the complete perimeter joint, rather than creating an unnecessarily thick bead at one location.
Cause | Why Do Tail-Lamp Corners and Bead Start/End Points Require Additional Process Control?
A perimeter tail-lamp joint normally requires the sealant bead to travel through several changes in direction before the end of the bead reconnects with its starting area.
Along straight or gently curved sections, nozzle speed can remain relatively stable. At sharper corners, nozzle direction needs to change. Excessive dwell time can create local accumulation, while overly rapid movement can reduce the bead cross-section.
Surface condition should also be separated from internal curing. 4C and 5C specify 20–40 minutes skin-over time, while 6C specifies 20–30 minutes. The cure rate is 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
For deeper lens-to-housing joints, actual sealant depth should therefore be considered when planning downstream assembly.
Solution | How Should 4C, 5C and 6C Be Selected According to Tail-Lamp Housing Geometry?
First identify the actual lens and rear-housing materials and their surface conditions. Then inspect joint width, depth, corner geometry and the start/end connection of the perimeter bead.
The documented product properties can then be compared.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A hardness and 1.4–1.6 MPa tensile strength, while 6C provides 60 Shore A hardness and 1.9–2.0 MPa tensile strength.
These properties represent different performance dimensions. Grade numbers or the highest value in one property should not be treated as an overall performance ranking.
A practical selection sequence is:
Lens Material → Rear-Housing Material → Joint Width/Depth → Corner and Bead Geometry → 4C/5C/6C Property Comparison → Sample Application → Cure Management → Tail-Lamp Assembly Verification
How It Works | How Does Silicone Sealant Create a Continuous Sealing Path Around an LSEV Tail Lamp?
Black silicone sealant is continuously applied along the actual connection joint between the tail-lamp lens and rear housing, filling the assembly gap to create a complete perimeter sealing path.
Along relatively straight sections, material delivery should be coordinated with nozzle travel speed. At curved edges and corners, nozzle direction should follow the lamp profile without interrupting the bead.
After completing the perimeter, the start/end connection should also be inspected. Adding more sealant to one area cannot compensate for a discontinuity elsewhere.
Where the joint contains a deeper sealant section, downstream processing should consider the specified cure rate rather than relying only on surface skin formation.
FAQ | What Are the Common Misunderstandings When Selecting Sealant for an Electric Microcar Tail Lamp?
Can curing time be ignored because the tail lamp is small?
No. Curing depends on the actual sealant section and joint depth. A small lamp does not necessarily mean a shallow sealant bead.
Does the 1.9–2.0 MPa tensile strength of 6C automatically make it the best choice for tail lamps?
No. Tensile strength is only one parameter. Hardness, skin-over time, cure rate, actual lamp materials and joint geometry should also be considered.
Can the product be marketed as suitable for every plastic tail lamp?
The supplied information supports lamp and plastic-component bonding and sealing, but does not provide dedicated adhesion data for every polymer grade. Actual lens and housing materials should therefore be verified.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |