Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
LSEV Tailgate Sheet-Metal Silicone Sealant For Hem And Overlap Joint Sealing
Problem | Why Does a Hemmed Tailgate Joint Still Require Careful Control of Sealant Continuity?
A Low-Speed Electric Vehicle tailgate is commonly formed by combining inner and outer sheet-metal panels. Compared with a simple straight sheet-metal joint, its perimeter can contain long edges, curved sections, hemmed areas and multiple corners.
As a result, the actual sealing path is not geometrically uniform.
If a constant material flow is used around the entire perimeter without adapting nozzle position to changes in hem width and corner geometry, some areas may receive sufficient material while others develop thinner bead sections.
The main inspection point should therefore be whether a continuous and reasonably uniform sealing path is formed along the
inner-to-outer panel connection, rather than whether a black bead is merely visible on the surface.
Cause | Why Are Tailgate Hem Corners and Panel Overlaps More Likely to Develop Variations in Sealant Quantity?
Long straight hem sections generally provide more consistent joint dimensions, making nozzle angle and travel speed easier to control.
At corners, curved areas and local overlap sections, the available application space and joint dimensions may change.
If the nozzle remains at a corner for too long while material flow continues, local accumulation can occur. If travel speed increases excessively during the directional change, the resulting bead can become thinner.
Different areas can also contain different sealant depths. 4C and 5C specify 20–40 minutes skin-over time, while 6C specifies 20–30 minutes. The cure rate is 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
Surface skin formation and internal curing should therefore be evaluated separately.
Solution | How Should 4C, 5C and 6C Be Selected for Tailgate Hem and Overlap Joints?
Begin by inspecting the actual tailgate construction, including inner-to-outer panel connections, hem width, overlap sections, corner geometry and joint depth.
The material properties can then be compared.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A hardness and 1.4–1.6 MPa tensile strength, while 6C provides 60 Shore A hardness and 1.9–2.0 MPa tensile strength.
Where the production process is sensitive to the surface working window after application, the 20–40 minute skin-over time of 4C/5C can also be compared with the 20–30 minute value of 6C.
A practical selection sequence is:
Tailgate Panels → Surface Condition → Hem/Overlap Geometry → Joint Width and Depth → 4C/5C/6C Properties → Sample Application → Cure Management → Tailgate Assembly Verification
How to Choose | Why Should Tensile Strength Not Be the Only Selection Criterion for Tailgate Seam Sealing?
Tensile strength is useful for comparing one mechanical property, but it does not independently determine suitability for the complete tailgate application.
For example, 6C specifies 1.9–2.0 MPa tensile strength, compared with 1.85 MPa for 4C and 1.4–1.6 MPa for 5C. However, 5C has a specified hardness of 65 Shore A, higher than the corresponding values of 4C and 6C.
Hardness and tensile strength therefore describe different material characteristics.
Actual joint dimensions, dispensing path, skin-over time and cure rate should also be considered. For deeper hem joints, the cure rate is particularly relevant to downstream process timing.
A grade should therefore not be described as the “best” simply because it has the highest value for one property.
Application Scenarios | Which Tailgate Sheet-Metal Joints Are Suitable for a Continuous Sealant Bead?
This application covers tailgate inner-to-outer panel hem areas, local sheet-metal overlap joints, transitions from long straight sections into corners, and other perimeter joint sections in low-speed electric vehicles.
The technical focus is continuous filling and sealing of the sheet-metal connection, rather than unsupported claims concerning corrosion protection, stone-chip resistance or specific vibration performance.
The available product information supports sealing applications on vehicle-body areas, but it does not provide dedicated adhesion data for every metal, coating or surface-treatment system. Verification with the actual tailgate panels is therefore appropriate before establishing a production process.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |