Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
LSEV Windshield A-Pillar Silicone Sealant For Glass-To-Frame Bonding And Sealing
Problem | Why Should Windshield-to-A-Pillar Joints Not Be Treated as Simple Straight Glass Seams?
The left and right edges of an LSEV windshield can form relatively long vertical joints along the A-pillar frame. However, these joints do not maintain exactly the same geometry from end to end.
As the sealing path approaches the upper and lower windshield corners, it transitions from a vertical section into curved or differently oriented areas.
This means the dispensing process must control both the long side bead and its transition into the corner sections.
If material flow remains constant while nozzle speed and angle change significantly at the corners, the resulting bead cross-section may differ from the straight middle section.
The objective is therefore to maintain continuous transitions between the long A-pillar bead and the upper and lower windshield corner joints.
Cause | Why Are the Upper and Lower Windshield Corners More Likely to Develop Variations in Sealant Thickness?
Along the middle section of the A-pillar, nozzle direction and travel speed can usually remain relatively stable.
Near the upper and lower corners, however, the sealing path changes from a vertical direction into a curved or more horizontal section.
If nozzle travel slows while material delivery remains unchanged, more sealant may be deposited per unit length. If the nozzle moves too quickly during the directional transition, the local bead can become thinner.
Skin-over time must also be distinguished from internal curing. 4C and 5C specify 20–40 minutes, while 6C specifies 20–30 minutes. Cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
A formed surface skin therefore does not demonstrate complete curing through a deeper glass-to-frame joint.
Solution | How Should 4C, 5C and 6C Be Selected According to Windshield A-Pillar Joint Geometry?
First identify the actual windshield surface, A-pillar frame material and surface condition. Joint width and depth should then be measured at the middle section and at both upper and lower corners.
The three grades can subsequently be compared.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A hardness and 1.4–1.6 MPa tensile strength, while 6C provides 60 Shore A hardness and 1.9–2.0 MPa tensile strength.
These values should be considered together with the actual joint structure rather than using the highest individual value to determine suitability.
A practical selection process is:
Windshield Surface → A-Pillar Frame Surface → Side-Joint Dimensions → Upper/Lower Corner Geometry → 4C/5C/6C Properties → Sample Application → Cure Management → Actual Windshield Assembly Verification
How It Works | How Does Silicone Sealant Connect the Long A-Pillar Bead with the Windshield Corner Joints?
Black silicone sealant is continuously dispensed along the actual connection between the windshield edge and A-pillar frame.
Along the relatively straight middle section, material flow and nozzle travel should be coordinated to maintain bead continuity. At the upper and lower corners, nozzle direction should follow the glass profile so that the bead transitions continuously into the adjacent sealing area.
The sections immediately before and after each corner should be inspected for discontinuities, unusually thin areas or excessive local accumulation.
Where sealant depth varies between sections, downstream assembly timing should also consider cure rate rather than treating skin-over time as complete cure time.
How to Choose | Which Selection Conditions Should Be Checked for Windshield A-Pillar Sealing?
The first factor is the actual substrate combination, including the windshield surface and A-pillar frame material and surface condition.
The second is joint geometry. The middle A-pillar section and the upper and lower corners may have different widths and depths, so one measurement point may not represent the complete sealing path.
The third factor is the material-property combination. Hardness, tensile strength, skin-over time and cure rate should be evaluated together with actual bead dimensions and production timing.
The available product information supports glass bonding and sealing in low-speed electric vehicle applications, but it does not provide dedicated adhesion data for every glass treatment, body metal or coating combination. Verification with the actual windshield and frame assembly is therefore appropriate.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |