Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
LSEV Front Body Panel Silicone Sealant For Sheet-Metal Splice, Overlap And Corner Joint Sealing
Problem | Why Should Different Front Body Panel Joints Not Be Treated as the Same Sealant-Bead Geometry?
The front body area of a low-speed electric vehicle can contain sheet-metal connections running in several directions. Unlike a single straight seam, joint direction, available application space and local geometry can change along the sealing path.
A bead may begin along a relatively regular splice, enter a panel overlap and then continue into a corner or restricted application area.
If exactly the same nozzle angle, travel speed and dispensing method are maintained throughout these different structures, the visible bead may appear continuous while the actual filling condition varies.
The key requirement is therefore sealant continuity between different panel connections and appropriate filling where the joint geometry changes.
Cause | Why Are Front Body Panel Overlaps, Corners and Narrow Joints More Likely to Develop Local Variations in Sealant Quantity?
Straight sheet-metal seams generally allow a relatively stable dispensing direction.
When the sealing path enters an overlap, corner or narrow working area, the angle between the nozzle and joint may change.
If nozzle travel slows to reach a restricted section while material delivery remains unchanged, the local bead may become thicker. If travel speed increases too much through a corner, the amount of sealant entering the joint may decrease.
Joint depth also affects cure management.
4C and 5C specify 20–40 minutes skin-over time, while 6C specifies 20–30 minutes. Cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
Surface skin formation therefore cannot replace evaluation of the internal curing process in deeper joints.
Solution | How Should 4C, 5C and 6C Be Selected According to Front Body Panel Joint Dimensions?
Before grade selection, divide the front body area into different joint types, such as straight splices, panel overlaps, corners and locally deeper seams, and confirm the actual surface condition of each component.
The 4C, 5C and 6C property combinations can then be compared.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A hardness and 1.4–1.6 MPa tensile strength, while 6C provides 60 Shore A hardness and 1.9–2.0 MPa tensile strength.
Where production timing depends on the working period after application, skin-over time should also be considered. For deeper joints, cure rate should be included in downstream process planning.
A practical selection sequence is:
Front Body Panels → Surface Condition → Joint Type → Width and Depth → Dispensing Path → 4C/5C/6C Properties → Sample Application → Cure Management → Actual Assembly Verification
How It Works | How Does Silicone Sealant Form a Continuous Filling Path Across Front Body Panel Joints Running in
Different Directions?
Black silicone sealant is continuously dispensed along the sheet-metal connections that require sealing.
Along regular straight sections, nozzle movement can remain relatively stable. When the bead enters an overlap, corner or area with different working space, nozzle direction should be adjusted according to the actual joint.
The objective is to keep the material filling the real connection rather than maintaining a visually identical surface bead while ignoring changes in joint dimensions.
For multi-section sealing paths, bead start/end points and transitions between different directions should also be inspected for discontinuities.
Application Scenarios | Which Front Body Sheet-Metal Connections Can Be Treated as Dedicated Sealing
Applications?
This application is intended for front body sheet-metal connections in low-speed four-wheel electric vehicles, Low-Speed Electric Vehicles (LSEVs) and electric microcars.
Typical locations include front panel splice seams, overlap areas between the front panel and adjacent body panels, corner joints and transitions from wider to narrower seams.
The technical focus is sheet-metal joint filling and sealing. The available product information does not provide comprehensive dedicated adhesion data for every vehicle-body metal, coating or surface-treatment system. Verification using the actual production components is therefore appropriate before establishing the final process.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |