Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
Electric Microcar Rear Body Panel Silicone Sealant For Rear-To-Side Panel Joint Sealing
Problem | Why Should Rear-to-Side Body Panel Corner Joints Not Be Sealed Like Simple Straight Sheet-Metal Seams?
The rear body section of an electric microcar is typically connected to adjacent body panels, including the left and right side panels. These connections can change from horizontal or vertical seams into corners and overlap areas.
Unlike a simple straight seam, the dispensing direction must change along the sealing path, while available working space may also vary.
If the entire joint is processed using one fixed nozzle angle and travel speed, the surface bead may appear continuous even though actual filling at corners, overlap edges and structural transitions is different.
The main objective is therefore continuous sealing through rear-to-side panel corners, sufficient filling of overlap joints and controlled transitions between beads running in different directions.
Cause | Why Are Rear-to-Side Panel Intersections More Likely to Develop Local Sealant Accumulation or Thin Bead Sections?
Along a regular straight joint, the nozzle can move at a relatively stable speed. When the bead reaches the corner between the rear and side panels, both nozzle angle and travel direction must change.
If nozzle movement slows while material delivery remains unchanged, local accumulation may occur. If the nozzle changes direction too quickly, the amount of sealant entering part of the joint can decrease.
Different overlap structures can also produce different bead depths.
4C and 5C specify 20–40 minutes skin-over time, while 6C specifies 20–30 minutes. Cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
Similar surface appearance therefore does not necessarily indicate the same internal curing condition at different joint depths.
Solution | How Should 4C, 5C and 6C Be Compared for Rear-to-Side Body Panel Corner Joints?
The actual rear panel, side panel and their surface conditions should first be inspected. Straight splices, panel overlaps, corners and locally deeper joints should be identified separately.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A hardness and 1.4–1.6 MPa tensile strength, while 6C provides 60 Shore A hardness and 1.9–2.0 MPa tensile strength.
These parameters should not be used individually to declare one grade universally more suitable. For example, 5C has the highest specified hardness, while 6C has the highest tensile-strength range. These values represent different material characteristics.
A practical selection sequence is:
Rear/Side Body Panels → Surface Condition → Overlap Type → Corner Geometry → Joint Width and Depth → 4C/5C/6C Properties → Sample Application → Cure Management → Body Assembly Verification
How It Works | How Does Silicone Sealant Maintain Continuous Filling Across Multi-Directional Rear Body Joints?
Black silicone sealant is continuously dispensed along the actual panel connections requiring sealing.
On regular straight sections of the rear panel, nozzle speed and material delivery can remain relatively stable. As the bead approaches the side-panel corner, nozzle direction should follow the actual panel geometry so that the sealant continues to fill the joint.
If the sealing path must be completed in multiple sections, the transition between separate bead sections should be inspected rather than simply covering the connection point with excessive surface material.
For locally deeper joints, downstream processing should consider the specified cure rate. Skin-over time should not be treated as complete through-cure time.
How to Choose | Which Conditions Should Be Confirmed When Selecting a Sealant for Rear Body Sheet-Metal Joints?
First evaluate the joint structure. Rear-to-side panel connections may contain straight sections, corners, overlaps and changes in joint dimensions.
Second, compare the material-property combination. Hardness, tensile strength, skin-over time and cure rate describe different aspects of the sealant and should not be reduced to a single-number comparison.
Third, identify the actual panel surface. The available product information does not provide dedicated adhesion data for every vehicle-body metal, coating or surface-treatment system.
For production use, verification with the actual rear and side body components is therefore appropriate.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |