Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
LSEV Door Lower Seam Silicone Sealant For Inner-To-Outer Panel Hem Joint Sealing
Problem | Why Does a Long, Apparently Straight Lower Door Hem Still Require Dedicated Application Control?
The lower section of an LSEV door often contains a relatively long inner-to-outer panel connection. Although this area appears more regular than an upper window-frame corner, actual construction may still include changes in hem width, local overlaps and front/rear corner transitions.
If the operator simply completes one long bead along the lower edge without checking the nozzle position relative to the actual joint, the middle section may remain consistent while the filling condition changes near the ends or other structural transitions.
Long continuous application paths are also sensitive to variations in nozzle travel speed. With the same material delivery rate, slower movement increases material per unit length, while excessive speed can produce a thinner bead.
The main control points are therefore stability along the long straight bead and continuous transitions into front/rear corners and local overlaps.
Cause | Why Can Bead Width and Depth Vary Along the Same Lower Door Sealing Path?
The middle section of a lower door edge generally provides a relatively long straight path, making nozzle direction easier to maintain.
Near the front and rear ends of the door, panel geometry changes and the nozzle must change direction. The inner-to-outer panel hem may also not maintain exactly the same dimensions across the entire lower edge.
Where a local joint is deeper, similar surface bead widths can still represent different internal bead dimensions.
4C and 5C specify 20–40 minutes skin-over time, while 6C specifies 20–30 minutes. Cure rates are 1.5–3 mm/24h for 4C and 1.2–3 mm/24h for 5C and 6C.
Simultaneous surface skin formation therefore does not establish identical internal curing progress in joints with different depths.
Solution | How Should 4C, 5C and 6C Be Selected for Lower Door Hem Joints?
Before selecting a grade, inspect the middle lower edge, front corner, rear corner and local overlap areas separately. Actual panel surface condition and joint dimensions should also be confirmed.
4C provides 50–60 Shore A hardness and 1.85 MPa tensile strength. 5C provides 65 Shore A hardness and 1.4–1.6 MPa tensile strength, while 6C provides 60 Shore A hardness and 1.9–2.0 MPa tensile strength.
For a long lower-door bead, skin-over time should be considered together with the production sequence. Where local joints are deeper, cure rate should also be included in downstream process planning.
A practical selection sequence is:
Inner/Outer Door Panels → Surface Condition → Lower Hem Geometry → Joint Width/Depth → Front/Rear Corners → 4C/5C/6C Properties → Sample Application → Cure Management → Door Assembly Verification
How It Works | How Does Silicone Sealant Form a Stable Continuous Sealing Path Along the Lower Door Edge?
Black silicone sealant is continuously dispensed along the lower inner-to-outer door panel connection so that material fills the required hem or overlap joint.
Along the long middle section, material delivery should be coordinated with nozzle travel speed to limit variations in bead dimensions.
As the sealing path approaches the front and rear ends of the door, nozzle direction should follow the actual panel profile, allowing the straight bead to transition continuously into the corner.
If application is interrupted, the connection between the existing and restarted bead should also be inspected. The objective is not to create the widest possible visible bead, but to maintain continuous filling along the actual joint.
FAQ | What Are the Common Misunderstandings When Selecting Sealant for Lower Door Sheet-Metal Joints?
Does the 65 Shore A hardness of 5C make it suitable for every lower door seam?
Not necessarily. Hardness is one selection parameter and should be considered together with joint dimensions, tensile strength, skin-over time and cure rate.
Does the 20–30 minute skin-over time of 6C mean complete curing after 20–30 minutes?
No. Skin-over time describes surface film formation. 6C specifies a cure rate of 1.2–3 mm/24h, so the two parameters should not be treated as equivalent.
Can lower door seam applications be marketed specifically for corrosion protection or stone-chip resistance?
The available information supports vehicle bonding and sealing applications and describes aging, UV and weather resistance, but does not provide dedicated lower-door corrosion-protection or stone-chip test data. Those claims should therefore not be added without corresponding verification.
Technical Specifications
|
Property |
4C |
5C |
6C |
|---|---|---|---|
|
Appearance |
Uniform Black Paste |
Uniform Black Paste |
Uniform Black Paste |
|
Density at 25°C |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
1.5–1.7 g/cm³ |
|
Volatile Content at 150°C |
3–4% |
3–4% |
3–4% |
|
Hardness |
50–60 Shore A |
65 Shore A |
60 Shore A |
|
Tensile Strength |
1.85 MPa |
1.4–1.6 MPa |
1.9–2.0 MPa |
|
Skin-Over Time |
20–40 min |
20–40 min |
20–30 min |
|
Cure Rate |
1.5–3 mm/24h |
1.2–3 mm/24h |
1.2–3 mm/24h |