Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
368 Silicone Weatherproof Sealant For Interior And Exterior Building Joints
Problem|Why Are Rigid Fillers Not Enough for Building Joints?
Building construction creates joints between window frames and walls, glass and metal frames, and different construction materials. These joints can be affected by temperature changes, thermal expansion and contraction, and normal movement between adjoining components.
When a joint is filled only with a rigid material, differences in substrate movement may contribute to cracking or loss of sealing continuity. For joints that need to remain sealed, the mechanical behavior and adhesion of the cured sealant therefore need to be considered.
Cause|How Does Temperature Affect Building Joints?
Glass, metal, wood and cement-based substrates have different thermal expansion and deformation characteristics. When two different materials form the sides of the same joint, they may not move by exactly the same amount as environmental temperatures change.
According to the 368 product data, its tensile modulus is >0.4 MPa at 23°C and >0.6 MPa at -20°C. These figures provide measurable references for evaluating the mechanical behavior of the sealant under different temperature conditions.
The product data also specifies no failure in adhesion at maintained extension and no failure after water immersion under the specified test conditions, providing additional references for joint adhesion performance.
Solution|Creating a Continuous Silicone Sealing Layer
368 Silicone Weatherproof Sealant is a one-component, neutral-curing silicone sealant designed for window and door installation, elastic building joints and general sealing involving glass, metal, wood, cement-based substrates and other compatible materials.
Its specified sag is ≤3 mm, tack-free time is ≤3 hours and extrusion rate is ≥150 mL/min. These parameters provide quantitative references for vertical application, surface skin formation and continuous dispensing.
For exterior vertical joints, sag is particularly relevant because excessive movement of uncured sealant can affect the finished bead profile.
The recommended application temperature is 5°C–40°C. Joint surfaces should be cleaned of dust, oil and other substances that may interfere with adhesion before application.
Technical Specifications
|
Property |
Specification |
|---|---|
|
Product Type |
One-component neutral silicone weatherproof sealant |
|
Appearance |
Homogeneous paste |
|
Sag |
≤3 mm |
|
Tack-Free Time |
≤3 h |
|
Extrusion Rate |
≥150 mL/min |
|
Tensile Modulus at 23°C |
>0.4 MPa |
|
Tensile Modulus at -20°C |
>0.6 MPa |
|
Adhesion at Maintained Extension |
No failure |
|
Adhesion after Water Immersion |
No failure |
|
Mass Loss |
≤20% |
|
Recommended Application Temperature |
5°C–40°C |
|
Standard |
JC/T 882-2001 |
|
Packaging |
300 mL cartridge / 590 mL sausage |
How It Works
After application, 368 establishes contact with the prepared surfaces on both sides of the joint. As the neutral silicone system cures, it forms a continuous elastomeric sealing layer.
When normal temperature changes or dimensional movement occur, the cured sealant needs to accommodate joint deformation while maintaining adhesion to both sides. Sealant selection alone is therefore not sufficient; joint dimensions, application depth, substrate preparation and bead finishing also influence actual sealing performance.
For joints designed to transfer structural loads, a structural silicone sealant should be selected according to the engineering requirements rather than substituting a general weatherproof sealant.
FAQ
Q1: Can 368 be used for exterior building joints?
Yes. The supplied product information identifies both indoor and outdoor construction and general building joints among its applications. Suitability should still be confirmed for the specific substrates and service conditions.
Q2: Is it suitable for vertical joints?
The specified sag value is ≤3 mm, providing a quantitative reference for vertical application performance.
Q3: Why is surface cleaning important before application?
Dust, oil, loose material and other contaminants can interfere with direct contact between the sealant and substrate, affecting the actual adhesion interface.
Q4: Can 368 be used as a structural silicone sealant?
It should not be treated as a structural silicone based on the current product information. Structural bonding applications require a product selected according to the relevant structural design and technical requirements.