Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
368 Weatherproof Silicone Sealant For Exterior Window Perimeter Joints
Problem|Why Are Exterior Window Perimeter Joints Critical?
After an exterior window is installed, an installation joint normally remains between the aluminum frame and the surrounding wall substrate. This joint connects materials with different physical characteristics and is located at the transition between indoor and outdoor environments.
Temperature changes and differences in substrate movement can affect the joint during service. Discontinuous application, insufficient sealant or inadequate adhesion can create weak points around the window perimeter.
Exterior window sealing therefore requires more than simply filling the visible gap. Application behavior, adhesion conditions, bead continuity and mechanical properties should all be considered.
Cause|Why Can Window Perimeter Seals Fail Locally?
Exterior window perimeter joints normally include vertical sections, horizontal sections and corner transitions.
Vertical joints place particular demands on the uncured sealant because excessive sag can alter the intended bead profile. According to the 368 product data, its sag is ≤3 mm, providing a quantitative reference for vertical application.
Surface condition is another important factor. Dust, oil and loose material can prevent direct contact between the sealant and the frame or wall substrate, affecting the actual adhesion interface.
Solution|Creating a Continuous Exterior Window Seal
368 Silicone Weatherproof Sealant is a one-component, neutral-curing silicone sealant intended for window installation and general sealing of compatible materials including glass, metal and cement-based construction substrates.
The product has a specified sag of ≤3 mm, tack-free time of ≤3 hours and extrusion rate of ≥150 mL/min. These parameters provide measurable references for vertical bead stability, surface skin formation and continuous dispensing.
For mechanical performance, the specified tensile modulus is >0.4 MPa at 23°C and >0.6 MPa at -20°C. The supplied technical data also states no failure for adhesion at maintained extension and no failure after water immersion under the specified test conditions.
The recommended application temperature is 5°C–40°C. Frame and wall surfaces should be properly prepared before sealant application.
Technical Specifications
|
Property |
Specification |
|---|---|
|
Product Type |
One-Component Neutral Silicone Weatherproof Sealant |
|
Appearance |
Homogeneous Paste |
|
Sag |
≤3 mm |
|
Tack-Free Time |
≤3 h |
|
Extrusion Rate |
≥150 mL/min |
|
Tensile Modulus at 23°C |
>0.4 MPa |
|
Tensile Modulus at -20°C |
>0.6 MPa |
|
Adhesion at Maintained Extension |
No Failure |
|
Adhesion after Water Immersion |
No Failure |
|
Mass Loss |
≤20% |
|
Recommended Application Temperature |
5°C–40°C |
|
Standard |
JC/T 882-2001 |
|
Packaging |
300 mL Cartridge / 590 mL Sausage |
How It Works
368 is continuously applied into the perimeter joint between the window frame and the building substrate. After curing, it forms a continuous silicone sealing layer along the connection.
Actual sealing performance depends not only on the sealant itself but also on joint dimensions, substrate preparation, continuous application and bead finishing.
Corner transitions deserve particular attention. A discontinuity between vertical and horizontal beads can interrupt the perimeter seal even when the straight sections appear properly filled.
How to Choose
For general exterior window perimeter sealing, three factors are particularly useful during product selection.
First, consider vertical application performance. The ≤3 mm sag value provides a measurable reference for maintaining the bead profile on vertical joints.
Second, consider mechanical data at different temperatures. The specified tensile modulus values of >0.4 MPa at 23°C and >0.6 MPa at -20°C provide quantitative information for product evaluation.
Third, confirm substrate compatibility. Specially coated aluminum, treated glass or unusual construction substrates should be evaluated before large-scale application.
368 is intended for weather sealing and general building joints and should not be substituted for a structural silicone in load-bearing structural glazing applications.