Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
368 Neutral Silicone Sealant For Glass And Aluminum Window Assembly
Problem|Why Do Glass-to-Aluminum Joints Require Proper Sealing?
Installing glass into an aluminum window frame involves more than simply holding the glass in position. Glass and aluminum have different physical characteristics and may respond differently when environmental temperatures change.
If the joint is discontinuous, poorly bonded or unevenly filled, the sealing integrity around the glazing area can be affected. Vertical edges and corners are particularly important because the uncured sealant needs to maintain a controlled bead profile before curing.
For B2B window fabrication and installation projects, sealant selection should therefore consider application behavior, mechanical properties and compatibility with the actual substrates.
Cause|Why Does the Glass-to-Aluminum Adhesion Interface Matter?
A glazing seal normally depends on adhesion at two interfaces: one between the sealant and glass, and another between the sealant and the aluminum frame.
Dust, oil and other contaminants on either surface can interfere with direct contact and reduce the quality of the actual adhesion interface. Vertical glazing joints also require the uncured material to resist excessive sagging.
368 has a specified sag value of ≤3 mm, providing a measurable reference for vertical application. Its extrusion rate of ≥150 mL/min provides an additional quantitative indicator for continuous gun application.
Solution|Neutral Silicone for General Glazing and Window Assembly
368 Silicone Weatherproof Sealant is a one-component, neutral-curing silicone sealant intended for window and door installation, glazing and general sealing of compatible construction materials.
The product has a specified tack-free time of ≤3 hours, sag of ≤3 mm, and extrusion rate of ≥150 mL/min. These parameters provide measurable references for surface skin formation, vertical bead stability and dispensing performance.
Its tensile modulus is specified as >0.4 MPa at 23°C and >0.6 MPa at -20°C, allowing mechanical behavior under different specified test temperatures to be considered during product selection.
The recommended application temperature is 5°C–40°C. Glass and aluminum bonding surfaces should be clean and free from contaminants before application. Adhesion compatibility should be verified when specially coated glass, treated aluminum or other unusual substrates are involved.
Technical Specifications
|
Property |
Specification |
|---|---|
|
Product Type |
One-component neutral silicone weatherproof sealant |
|
Appearance |
Homogeneous paste |
|
Sag |
≤3 mm |
|
Tack-Free Time |
≤3 h |
|
Extrusion Rate |
≥150 mL/min |
|
Tensile Modulus at 23°C |
>0.4 MPa |
|
Tensile Modulus at -20°C |
>0.6 MPa |
|
Adhesion at Maintained Extension |
No failure |
|
Adhesion after Water Immersion |
No failure |
|
Mass Loss |
≤20% |
|
Recommended Application Temperature |
5°C–40°C |
|
Standard |
JC/T 882-2001 |
|
Packaging |
300 mL Cartridge / 590 mL Sausage |
How to Choose
The first step is to distinguish between general glazing sealing and structural bonding. For perimeter glazing joints and general window assembly, substrate compatibility, sag, extrusion performance and mechanical behavior under different temperatures are useful selection criteria.
For vertical glazing edges, the ≤3 mm sag value is particularly relevant. For fabrication or installation work requiring continuous dispensing, the ≥150 mL/min extrusion rate provides another measurable application parameter.
If the silicone joint is designed to transfer structural loads between glass and framing, a structural silicone product should be selected according to the specific structural glazing design requirements.
FAQ
Q1: Can 368 be used between glass and aluminum frames?
The supplied product information includes window installation, glass and metal among its general sealing applications. Suitability should still be confirmed for special coatings or surface treatments.
Q2: Is it suitable for vertical glazing joints?
The specified sag value is ≤3 mm, which provides a measurable reference for vertical application performance.
Q3: Does a tack-free time of ≤3 hours mean the sealant is fully cured after three hours?
No. Tack-free time refers to surface skin formation and should not be interpreted as full-depth cure time.
Q4: Can it be used for structural glazing?
368 should not be classified as a structural glazing silicone based on the current product data. Structural applications require a sealant selected according to the relevant structural design requirements.