Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
368 Neutral Silicone Sealant for Glass and Window Frame Sealing
Problem|Why Does Glazing Require Both Sealing and Application Control?
During window glazing, joints are commonly formed between glass and aluminum or other frame materials. These joints require a continuous seal while also involving vertical edges, corners and interfaces between different materials.
Discontinuous dispensing can leave underfilled sections, while excessive sag on vertical edges can produce an uneven bead profile. Glass and metal framing may also respond differently to environmental temperature changes.
Sealant selection for glazing should therefore consider application characteristics, mechanical data and substrate suitability rather than relying only on the appearance of the freshly applied bead.
Cause|Why Are Glass Edges and Corners Important?
A typical glazing perimeter includes horizontal edges, vertical edges and four corner transitions. Changes in application direction can create excessive material or discontinuities if gun speed and sealant output are not properly controlled.
368 has a specified extrusion rate of ≥150 mL/min, providing a measurable reference for continuous dispensing. Its sag value is ≤3 mm, which provides a quantitative reference for maintaining the sealant profile on vertical glazing joints.
Dust, oil and other contaminants on glass or framing can also interfere with the sealant-to-substrate interface. Surface preparation is therefore an essential part of glazing seal application.
Solution|Neutral Silicone for Continuous Glazing Seals
368 Silicone Weatherproof Sealant is a one-component, neutral-curing silicone sealant intended for glass, window and general construction sealing applications within its specified use range.
The supplied product data specifies a tack-free time of ≤3 hours, sag of ≤3 mm and extrusion rate of ≥150 mL/min. These values provide measurable references for surface skin formation, vertical application and dispensing performance.
Its tensile modulus is >0.4 MPa at 23°C and >0.6 MPa at -20°C. Under the specified test conditions, the technical data also states no failure in adhesion at maintained extension and no failure in adhesion after water immersion.
These measurable parameters provide B2B window manufacturers, installers and buyers with more useful technical information than general claims such as “strong adhesion” or “excellent weather resistance.”
The recommended application temperature is 5°C–40°C. Glass and frame surfaces should be properly cleaned before application. Compatibility should be confirmed for coated glass, specially treated metal or other unusual substrates.
Technical Specifications
|
Property |
Specification |
|---|---|
|
Product Type |
One-Component Neutral Silicone Weatherproof Sealant |
|
Appearance |
Homogeneous Paste |
|
Sag |
≤3 mm |
|
Tack-Free Time |
≤3 h |
|
Extrusion Rate |
≥150 mL/min |
|
Tensile Modulus at 23°C |
>0.4 MPa |
|
Tensile Modulus at -20°C |
>0.6 MPa |
|
Adhesion at Maintained Extension |
No Failure |
|
Adhesion after Water Immersion |
No Failure |
|
Mass Loss |
≤20% |
|
Recommended Application Temperature |
5°C–40°C |
|
Standard |
JC/T 882-2001 |
|
Packaging |
300 mL Cartridge / 590 mL Sausage |
How It Works
368 is continuously applied between the glass edge and the surrounding frame. After suitable surface preparation and bead finishing, the sealant establishes contact with both sides of the joint and cures into a continuous elastomeric sealing layer.
Continuity around the entire glazing perimeter is important, especially at corner transitions. Applying additional material to one section cannot compensate for a discontinuity elsewhere.
For vertical glass edges, the specified ≤3 mm sag provides a reference for bead stability. For longer continuous joints, the ≥150 mL/min extrusion rate provides a measurable indication of dispensing performance.
How to Choose
The first step is to determine the function of the glazing joint.
For general window glazing, perimeter sealing and non-structural assembly, product selection can consider curing system, substrate compatibility, sag, extrusion performance and mechanical data at different temperatures.
If the sealant joint is intended to transfer structural loads between glass and framing, the application requires a structural silicone selected according to the relevant engineering design requirements.
The inclusion of glass in the product's application range should also not be interpreted as universal compatibility with every glass surface. Coated or specially treated glass should be evaluated before large-scale use.