Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
368 Neutral Silicone Sealant for Building Joints Under Low-Temperature Conditions
Problem|Why Does Temperature Matter for Building Joints?
Window perimeter joints, glazing joints and connections between different building materials are not completely static. Changes in environmental temperature can cause aluminum, glass, cement-based substrates and other materials to undergo different dimensional changes.
In colder climates or locations with significant temperature variation, selecting a sealant only according to its application behavior at room temperature provides limited information. Mechanical properties measured under different temperature conditions can provide additional data for product evaluation.
Sealant selection should therefore consider application temperature, tensile modulus, adhesion characteristics and the actual joint design.
Cause|Why Compare Tensile Modulus at 23°C and -20°C?
Tensile modulus provides information about the mechanical response of a material under specified deformation conditions. Silicone properties can change as temperature changes.
According to the supplied 368 product data, the tensile modulus is >0.4 MPa at 23°C and >0.6 MPa at -20°C.
For B2B buyers and technical teams, these figures provide more useful information than a general statement such as “good low-temperature performance,” because they identify measurable properties at specified test temperatures.
However, the -20°C modulus value must not be confused with the application temperature. The recommended application temperature stated in the product information is 5°C–40°C.
Solution|Use Measurable Temperature Data for Joint Selection
368 Silicone Weatherproof Sealant is a one-component, neutral-curing silicone sealant intended for window installation, glazing and general building joint sealing.
In addition to its tensile modulus data, the technical information specifies no failure in adhesion at maintained extension and no failure in adhesion after water immersion under the specified test conditions.
For application performance, the product has a sag value of ≤3 mm, tack-free time of ≤3 hours and extrusion rate of ≥150 mL/min.
These parameters allow contractors and buyers to consider both application characteristics and mechanical behavior when selecting a sealant for building joints exposed to temperature changes.
For cold-season construction, the stated 5°C–40°C application temperature range should still be followed. A modulus value measured at -20°C does not by itself justify application below the recommended installation temperature.
Technical Specifications
|
Property |
Specification |
|---|---|
|
Product Type |
One-Component Neutral Silicone Weatherproof Sealant |
|
Appearance |
Homogeneous Paste |
|
Sag |
≤3 mm |
|
Tack-Free Time |
≤3 h |
|
Extrusion Rate |
≥150 mL/min |
|
Tensile Modulus at 23°C |
>0.4 MPa |
|
Tensile Modulus at -20°C |
>0.6 MPa |
|
Adhesion at Maintained Extension |
No Failure |
|
Adhesion after Water Immersion |
No Failure |
|
Mass Loss |
≤20% |
|
Recommended Application Temperature |
5°C–40°C |
|
Standard |
JC/T 882-2001 |
|
Packaging |
300 mL Cartridge / 590 mL Sausage |
How It Works
When the materials on both sides of a building joint respond to temperature changes, the joint may undergo dimensional movement. The cured silicone layer between the substrates needs to respond mechanically while maintaining contact with the joint surfaces.
The specified tensile modulus values of >0.4 MPa at 23°C and >0.6 MPa at -20°C provide measurable references for understanding the material under two specified temperature conditions.
Actual joint performance also depends on joint dimensions, sealant depth, substrate preparation and the amount of movement encountered in service. Modulus data should therefore be used as one part of product selection rather than as a stand-alone prediction of service life or minimum operating temperature.
FAQ
Q1: What does a tensile modulus of >0.6 MPa at -20°C mean?
It describes the specified tensile modulus of the material under the -20°C test condition. It is a mechanical property, not an application-temperature rating.
Q2: Can 368 be applied at -20°C?
The supplied product information does not support that claim. The recommended application temperature is 5°C–40°C.
Q3: Why are both 23°C and -20°C modulus values useful?
They provide quantitative references for comparing mechanical behavior under different specified temperature conditions.
Q4: Can the product be marketed as an “extreme cold sealant”?
The current data does not support such a broad claim. A technically accurate statement is that the specified tensile modulus is >0.6 MPa at -20°C.