Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
368 Easy-Extrusion Silicone Sealant for Continuous Window and Building Joint Application
Problem|Why Do Long Joints Develop Discontinuous Sealant Beads?
Window perimeters, glazing edges and connections between construction materials often contain relatively long continuous joints. During installation, the sealant needs to be dispensed through a gun while maintaining a controlled bead along the joint.
If dispensing becomes inconsistent, installers may compensate by changing gun speed. This can result in excessive material in some sections, insufficient filling in others or interruptions in the sealant bead.
For continuous building joints, extrusion performance is therefore a useful application parameter in addition to cured mechanical and adhesion properties.
Cause|Why Does Extrusion Performance Matter?
A continuous sealant bead depends on coordination between material output and movement of the application gun.
According to the supplied technical data, 368 has an extrusion rate of ≥150 mL/min. This provides a measurable reference for dispensing performance rather than relying on subjective claims such as “easy to apply.”
However, extrusion rate should not be interpreted as actual project productivity. Gun type, ambient temperature, nozzle opening, joint dimensions and installer technique can all influence the real application rate.
The ≥150 mL/min value should therefore be used as a product performance parameter rather than as a direct estimate of how many meters of joint can be completed within a given time.
Solution|Combining Extrusion Performance with Vertical Bead Control
368 is a one-component, neutral-curing silicone sealant intended for window installation, glazing and general building joint sealing.
Its extrusion rate of ≥150 mL/min provides a measurable reference for continuous application around window frames and glazing joints. At the same time, the product has a sag value of ≤3 mm, which provides information about bead stability on vertical joints.
These parameters describe two different aspects of application: extrusion rate relates to dispensing from the package, while sag relates to the ability of the uncured material to maintain its profile after vertical application.
The product also has a tack-free time of ≤3 hours, with tensile modulus values of >0.4 MPa at 23°C and >0.6 MPa at -20°C. Under the specified test conditions, adhesion at maintained extension and adhesion after water immersion are both reported as no failure.
The recommended application temperature is 5°C–40°C.
Technical Specifications
|
Property |
Specification |
|---|---|
|
Product Type |
One-Component Neutral Silicone Weatherproof Sealant |
|
Appearance |
Homogeneous Paste |
|
Sag |
≤3 mm |
|
Tack-Free Time |
≤3 h |
|
Extrusion Rate |
≥150 mL/min |
|
Tensile Modulus at 23°C |
>0.4 MPa |
|
Tensile Modulus at -20°C |
>0.6 MPa |
|
Adhesion at Maintained Extension |
No Failure |
|
Adhesion after Water Immersion |
No Failure |
|
Mass Loss |
≤20% |
|
Recommended Application Temperature |
5°C–40°C |
|
Standard |
JC/T 882-2001 |
|
Packaging |
300 mL Cartridge / 590 mL Sausage |
How It Works
During application, pressure from the sealant gun pushes the material through the nozzle and into the prepared joint. For longer perimeter joints, consistent dispensing helps the installer maintain a controlled sealant bead.
The specified ≥150 mL/min extrusion rate provides a quantitative reference for this dispensing behavior.
A higher extrusion value should not be interpreted as a requirement to apply the sealant as quickly as possible. Gun speed should still be adjusted according to joint width and depth to achieve adequate filling.
For vertical joints, the ≤3 mm sag value should also be considered so that dispensing performance and bead stability are evaluated together.
Application Scenarios
368 can be used for long perimeter joints around aluminum windows, continuous glazing joints, door frame installation joints and other compatible building material connections.
For window fabrication and on-site continuous sealing, the ≥150 mL/min extrusion rate provides B2B buyers and installers with a measurable application parameter.
Structural glazing or other load-bearing bonding applications require a product selected according to the relevant engineering requirements rather than extrusion performance alone.