logo

Silver Die Attach Automotive Electronic Bonding Heat Curing Epoxy Adhesive For Chips

Place of Origin: China
Brand Name: YT
Certification: ISO9001, Work safety standardization certificate
Model Number: Epoxy Adhesive
Inquiry Now
Get A Quote
Specifications
Highlight Features

die attach silver epoxy adhesive

,

silver epoxy adhesive for automotive

,

one component silver conductive epoxy adhesive

Product Name:
Epoxy Die Attach Adhesive
Material System:
Conductive Silver Epoxy
Component And Cure:
One-component, Heat-curing
Typical Thermal Conductivity:
8 W/(m·K)
Typical Volume Resistivity:
1.0 × 10⁻⁴ Ω·cm
Typical Die Shear At 25°C:
10.2 Kgf; 2 Mm × 2 Mm, Si-Ag
Recommended Curing Schedule:
175°C For 1.0 Hour
Application:
Bonding And Securing Automotive-grade IC And LED Chips
Product Description

One-Component Conductive Epoxy Die Attach Adhesive For Automotive-Grade IC And LED

 

Product Positioning

 

This one-component, heat-curing conductive silver epoxy is intended for bonding and securing automotive-grade IC and LED chips. Selection should address electrical conduction, heat transfer, adhesion and dispensing requirements, together with frozen storage, thawing and curing conditions.

 

Key Specifications

 

Item

Document specification

Typical value or handling requirement

Material and curing system

One-component, heat-curing conductive silver adhesive

Epoxy system identified in the product name

Appearance

Silver

Silver

Density

3.4–3.8 g/cm³

3.6 g/cm³

Viscosity

8,500–11,000 cP

10,000 cP; 5 rpm, spindle No. 51

Thixotropic index

4.0–5.0

4.5; 0.5 rpm / 5 rpm

Die shear at 25°C

10.0 kgf

10.2 kgf; 2 mm × 2 mm, Si-Ag

Die shear at 160°C

1.5 kgf

1.5 kgf; 2 mm × 2 mm, Si-Ag

Thermal conductivity

Approximately 8 W/(m·K)

8 W/(m·K); laser flash method

Volume resistivity

<2 × 10⁻⁴ Ω·cm

1.0 × 10⁻⁴ Ω·cm; standard curing conditions

Recommended cure

—

175°C for 1.0 hour

Thawing

—

60–90 minutes at room temperature; keep the syringe upright

Use after thawing

—

Use within 36 hours at 23°C and 50% RH

Packaging

—

5 cc or 10 cc

Storage and shelf life

—

Original packaging at ≤−40°C; six months from manufacture

 

Problem | Why Must Die Attachment Address Both Conduction and Heat Transfer?

 

IC and LED die attachment requires more than checking whether the chip remains bonded. The adhesive layer must also meet the application's electrical and heat-transfer requirements. Tailing, stringing or variations in dispensed quantity can make bondline geometry harder to control.

 

Cause | Material Properties Must Be Assessed Alongside the Bondline

 

Thermal conductivity and volume resistivity describe material properties. Actual interface performance also depends on bondline thickness, coverage and degree of cure. The typical thermal conductivity of 8 W/(m·K) cannot, by itself, predict the cooling performance of a complete device. Surface contamination can also affect adhesion.

 

Solution | Control Thawing, Dispensing and Curing Together

 

Keep the syringe upright and thaw it at room temperature for 60–90 minutes before dispensing. At 23°C and 50% RH, use the thawed adhesive within the recommended 36-hour period. Repeated freezing and thawing is not permitted. The recommended cure is 175°C for one hour; verify chip and substrate compatibility with this temperature before production use.

 

Application | Use Within the Documented Die Attachment Scope

 

The documented application is bonding and securing automotive-grade IC and LED chips. Specific die sizes, substrate finishes and package configurations require sample validation. The stated use should not be expanded into general electronic potting or complete lamp sealing.

 

How It Works | How Do Electrical and Thermal Properties Work Together?

 

The cured conductive silver adhesive forms the die attachment interface. Its typical volume resistivity of 1.0 × 10⁻⁴ Ω·cm supports assessment of material conductivity. Heat-transfer performance must also be evaluated against the actual bondline structure.

 

How to Choose | Which Conditions Should Be Checked First?

 

Check electrical requirements, curing-temperature compatibility and frozen-storage capability before assessing dispensing suitability. The typical die shear result of 10.2 kgf at 25°C applies to the stated 2 mm × 2 mm, Si-Ag test conditions. Compare results under similar conditions rather than treating this value as the load capacity of any chip.

Related Products
Send An Inquiry