Quick Link
Quick Contact
Address
No. 1707, Industrial Road, Tangshan Town, Huantai County, Zibo City, Shandong Province
Tel
86-533-17860959591
Our Newsletter
Subscribe to our newsletter for discounts and more.
One-Component Heat-Curing Conductive Silver Adhesive For IC And LED Dispensing With Defined Thawing And Working-Time Requirements
Product Positioning
This one-component, heat-curing conductive silver epoxy is intended for bonding and securing automotive-grade IC and LED chips. The document describes no tailing or stringing and low moisture absorption. For dispensing applications, selection should consider rheological data, thawing requirements and the recommended working period together, rather than relying on initial viscosity alone.
Specifications
Item | Document specification or requirement | Typical value / test conditions |
|---|---|---|
Product system | One-component, heat-curing conductive silver adhesive | Epoxy system |
Appearance | Silver | Silver |
Viscosity | 8,500–11,000 cP | 10,000 cP; 5 rpm, spindle No. 51 |
Thixotropic index | 4.0–5.0 | 4.5; 0.5 rpm / 5 rpm |
Thermal conductivity | Approximately 8 W/(m·K) | Typical value: 8 W/(m·K) |
Volume resistivity | <2 × 10⁻⁴ Ω·cm | Typical value: 1.0 × 10⁻⁴ Ω·cm; standard curing conditions |
Thawing | 60–90 minutes at room temperature | Keep the syringe upright |
Use after thawing | Recommended use within 36 hours | 23°C, 50% RH; no repeated freezing and thawing |
Recommended cure | 175°C for 1.0 hour | — |
Packaging | 5 cc or 10 cc | Available according to requirements |
Storage and shelf life | Original packaging at ≤−40°C | Six months from manufacture |
Problem | Does String-Free Dispensing Establish Production Readiness?
Chip dispensing requires assessment of adhesive cutoff, shot quantity, placement and adhesive distribution after die placement. Even when a material is described as having no tailing or stringing, equipment trials remain necessary. Thawing and working-time controls must also be included.
Cause | One Viscosity Value Cannot Fully Describe Dispensing Behaviour
The typical viscosity is 10,000 cP at 5 rpm using spindle No. 51. The typical thixotropic index is 4.5, based on measurements at 0.5 rpm and 5 rpm. These values describe flow characteristics under specified measurement conditions. They cannot directly determine dispensing pressure, needle size or shot quantity.
Solution | Organise Material Handling Around Recorded Times
After removal from frozen storage, keep the syringe upright and thaw it at room temperature for 60–90 minutes. Use it on the dispensing equipment promptly after thawing. Record removal, thaw completion and start-of-use times. At 23°C and 50% RH, use within the recommended 36-hour period. Repeated freezing and thawing must not be used to extend usability.
Application | IC and LED Die Attachment Processes
The documented application is attachment of automotive-grade IC and LED chips. Process validation can address material handling, thawing, dispensing or dipping, die placement and heat curing. Needle selection, dispensing patterns and bondline thickness are unspecified and require sample assessment.
How to Choose | Match Package Size to Material Consumption
Select between 5 cc and 10 cc packaging according to shift consumption and equipment scheduling. The key considerations are whether thawed material can be consumed within the recommended period and whether storage in its original packaging at ≤−40°C is available.
FAQ | What Are the Handling and Curing Limits?
Does the 36-hour recommendation apply to every production environment?
It applies to 23°C and 50% RH. It should not automatically be transferred to other conditions.
Can the curing time be shortened?
The document recommends 175°C for one hour and provides no alternative schedule. Any adjustment requires validation of curing and bonding results.