logo

Automotive Grade Silver Conductive LED Chip Bonding Epoxy Adhesive For Assembly

Place of Origin: China
Brand Name: YT
Certification: ISO9001, Work safety standardization certificate
Model Number: Epoxy Adhesive
Inquiry Now
Get A Quote
Specifications
Highlight Features

epoxy adhesive led

,

chips silver conductive glue

,

automotive grade epoxy adhesive

Product Name:
Heat-Curing Epoxy Die Attach Adhesive
Material System:
Conductive Silver Epoxy
Component And Cure:
One-component, Heat-curing
Typical Thermal Conductivity:
8 W/(m·K)
Typical Volume Resistivity:
1.0 × 10⁻⁴ Ω·cm
Typical Die Shear At 25°C:
10.2 Kgf; 2 Mm × 2 Mm, Si-Ag
Recommended Curing Schedule:
175°C For 1.0 Hour
Application:
Bonding And Securing Automotive-grade IC And LED Chips
Product Description

Epoxy Die Attach Adhesive | One-Component Heat-Curing Conductive Silver Epoxy For IC And LED Attachment With Defined Curing Requirements
 
Product Positioning
This one-component, heat-curing conductive silver epoxy is intended for bonding and securing automotive-grade IC and LED chips. It requires no on-site two-component proportioning or mixing, while storage, thawing, working time and heat curing still require control. Selection should establish compatibility with production equipment, component temperature limits and scheduling.
 
Specifications
 

Item

Document specification or requirement

Typical value or conditions

Material system

Conductive silver epoxy

One-component, heat-curing

Recommended cure

175°C for 1.0 hour

No alternative curing schedule provided

Room-temperature thawing

60–90 minutes

Keep the syringe upright

Use after thawing

Recommended use within 36 hours

23°C, 50% RH

Freeze–thaw requirements

Repeated freezing and thawing is not permitted

Use promptly on equipment after thawing

Viscosity

8,500–11,000 cP

Typical value: 10,000 cP; 5 rpm, spindle No. 51

Die shear at 25°C

10.0 kgf

Typical value: 10.2 kgf; 2 mm × 2 mm, Si-Ag

Thermal conductivity

Approximately 8 W/(m·K)

Typical value: 8 W/(m·K)

Volume resistivity

<2 × 10⁻⁴ Ω·cm

Typical value: 1.0 × 10⁻⁴ Ω·cm

Packaging

5 cc or 10 cc

Available according to requirements

Storage and shelf life

Original packaging at ≤−40°C

Six months from manufacture

 
Problem | Can a One-Component Adhesive Be Introduced Directly into an Existing Process?
 
A one-component material removes on-site two-component proportioning, but this does not establish compatibility with an existing oven programme. Chip and substrate temperature compatibility, heating and holding arrangements require assessment before introduction. Heating capability alone does not establish process suitability.
 
Cause | Curing Temperature and Time Must Be Considered Together
 
The recommended cure is 175°C for one hour. Temperature and time should be treated as a combined condition. The document provides no relationship for longer curing at lower temperatures or shorter curing at higher temperatures. It also does not define the timing start point, so an equivalent schedule cannot be assumed.
 
Solution | Confirm Process Conditions Before Validating Samples
 
Confirm the curing-time start point and recommended heating requirements with technical support, and record actual sample temperatures. Keep bonding surfaces clean and follow the thawing, dispensing and curing instructions during trials. Then assess bonding and electrical performance. Changes in loading or programme settings should prompt a check of their effect on sample curing conditions.
 
Application | Heat-Cured IC and LED Die Attachment
 
The documented application is attachment of automotive-grade IC and LED chips. Assess compatibility with the actual die, substrate and packaging process. If components cannot accommodate the recommended cure, obtain a supported alternative process before reducing the temperature.
 
How to Choose | Include the Working Period in Production Scheduling
 
At 23°C and 50% RH, use the thawed adhesive within the recommended 36-hour period. Select 5 cc or 10 cc packaging according to consumption and record thawing and equipment-use times. This working period must not be interpreted as permission to wait 36 hours after die placement before curing.
 
FAQ | What Are Common Misinterpretations of Curing and Storage Data?
 
Does 175°C establish a continuous service temperature?
No. It is the recommended curing temperature. The document does not establish a continuous operating range from this value.

Can unused adhesive be frozen again?
Repeated freezing and thawing is not permitted. Control remaining quantities through package selection and material scheduling.

Related Products
Send An Inquiry